Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
10.1. Specifications
10.2. General information
10.3. Epiploons replacement
10.4. Manual transmission removal and installation
10.5. 5 step check points of the FS5W71B/C types dismantling
10.6. 4-staged check points of the F4W71B and S types - dismantling
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





10-4-mekhanicheskaya-kpp-snyatie-i-ustanovka.html

10.4. Manual transmission removal and installation

1. Disconnect the battery from weight.
2. Disconnect draft of a butterfly valve in salon.
3. Remove section of the forward panel (Hl. 13).
4. Remove a cover from the check point lever.

3.11 Редуктор спидометра на заднеприводных автомобилях
3.11 A speedometer reducer on rear wheel drive cars


3.5а Штифт рычага КПП (на а/м ранних выпусков)
3.5a a check point lever Pin (on the car of early releases)


3.5б Пружинное кольцо рычага КПП (на  а/м  поздних выпусков)
3.5b the Spring ring of the lever of the check point (on the car of late releases)


5. Transfer the lever to neutral situation, get a lock washer, a pin (or a spring lock ring) and remove the lever (photo).
6. Lift the car on the sufficient height that it was possible to take the check point from under the car.
7. Remove a forward exhaust pipe.
8. On all-wheel drive cars remove the forward driveshaft (Hl. 9). Substitute a prop under a forward reducer and remove a back cross-piece of a reducer. If necessary remove a forward reducer (Hl. 9).
9. Disconnect half shafts (Hl. 8) also muffle openings in the check point.
10. Disconnect wires from all switches of the check point
11. Disconnect a cable of a speedometer (photo).
12. Merge oil from the check point.
13. Remove the working cylinder of coupling and take aside.
14. Establish supports under the engine and under the check point.
15. Turn off nuts of a support of the check point and bolts of fastening of an arm to a frame, remove a support.
16. Remove a starter.
17. Turn off bolts of a case of coupling (photo).
18. At the same time lower supports so that the check point could be removed from the engine and to lower, without assuming that the weight of the check point was perceived by a main shaft.
19. Installation is carried out upside-down. Grease before assembly of a vent of a main shaft, detail of the mechanism of inclusion of transfers, center a clutch plate and adjust the pedal course.

3.17 Подпорка картера КПП из брусков
3.17 A check point case prop from whetstones


4.5 Снятие редуктора спидометра
4.5 Removal of a reducer of a speedometer


4.7 Выворачивание заглушки .
4.7 Cap reversing.


4.4 Выверните из картера КПП выключатели
4.4 Turn out switches from a check point case



"previous page
10.3. Epiploons replacement
following page"
10.5. 5 step check points of the FS5W71B/C types dismantling