Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
11.1. Specifications
11.2. General data
11.3. Draft of management of transmission - adjustment
11.4. The blocking switch - check and adjustment
11.5. Kick-down - the switch - adjustment
11.6. A rod of a vacuum diaphragm - adjustment
11.7. A back epiploon - replacement
11.8. Automatic transmission - removal and installation
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





11-3-tyaga-upravleniya-transmissiejj-regulirovka.html

11.3. Draft of management of transmission - adjustment

Cars with the floor selector
1. Translate the selector from situation P in "1", at the same time operation of a clamp in all intermediate positions has to be felt. If operation is not felt, or the index does not coincide with designations, then draft needs to be adjusted.
2. Transfer the selector to situation P.
3. Release lock-nuts (photo).
Rear wheel drive cars
4. Tighten a lock-nut of X (photo) against the stop in a selector arm, pressing the lever in the direction of situation R (not to press the button).
5. Turn off a lock-nut of X on 1/2-1/4 turn and tighten with the set moment.
All-wheel drive cars since 1987.
6. Pressing the lever in the direction of situation R (not to press the button), tighten a screw coupler until the coupler is not combined with a vein of a cable (photo).
7. Turn off a coupler on 1 turn and tighten lock-nuts with the set moment.

2.11 Контргайки тяги автоматической трансмиссии на автомобилях 1987-88 г.г. с селектором на рулевой колонке
2.11 Lock-nuts of draft of automatic transmission on cars of 1987-88 with the selector on a steering column


2.5 Adjustment of draft in cars with the floor selector (all-wheel drive cars of 1988 and all rear-wheel cars since 1987) 1. Sector        of "P" 2. Lock-nut of X 3. Lock-nut Y 4. Not to press


2.6 Регулировка тяги трансмиссии на полноприводных автомобилях (с 1987 г).
2.6 Adjustment of draft of transmission on all-wheel drive cars (since 1987).


8. Translate the selector from situation P in "1" and be convinced of smoothness of the course of the selector.
Cars with the selector on a steering column
9. Translate the selector from situation P in "1", at the same time operation of a clamp in all intermediate positions has to be felt. If operation is not felt, or the index does not coincide with designations of sectors, then draft needs to be adjusted.

2.12 Регулировка тяги трансмиссии на автомобилях 1987-88 г.г. с селектором на рулевой колонке 1. Контргайка А        2. Позиционная пластина  3. Контргайка В   4. Не нажимать
2.12 Adjustment of draft of transmission on cars of 1987-88 with the selector on a steering column 1. Lock-nut       A 2. Position plate 3. Lock-nut  B 4. Not to press


3.3 Проверка цепи между выводами датчика в различных положениях селектора 1.  Диаграмма замкнутых выводов в различных положениях селектора
3.3 Check of a chain between sensor conclusions in various provisions of the selector 1. The chart of the closed conclusions in various provisions of the selector


3.5б Типичное расположение болтав блокирующего переключателя(показаны для полноприводных автомобилей 1987 - 88 г.г.)
3.5b the Typical arrangement of bolts of the blocking switch (are shown for all-wheel drive cars 1987 - 88)


10. Transfer the selector to situation P.
11. Release lock-nuts (photo).
12. Tighten a lock-nut And (photo) against the stop in an arm, pressing the lever in the direction of situation R (not to press the button).
13. Turn off a lock-nut And on 2 turns and tighten a nut In with the set moment.
14. Translate the selector from situation P in "1" and be convinced of smoothness of the course of the selector


"previous page
11.2. General data
following page"
11.4. The blocking switch - check and adjustment