Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
11.1. Specifications
11.2. General data
11.3. Draft of management of transmission - adjustment
11.4. The blocking switch - check and adjustment
11.5. Kick-down - the switch - adjustment
11.6. A rod of a vacuum diaphragm - adjustment
11.7. A back epiploon - replacement
11.8. Automatic transmission - removal and installation
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





11-8-avtomaticheskaya-transmissiya-snyatie-i-ustanovka.html

11.8. Automatic transmission - removal and installation

Attention!
The car should be lifted on sufficient height to get transmission.

All works on repair of transmission are performed in car service.
1. Consider the malfunction codes brought in memory of the processor block in car service, and establish a transmission cause of defect.
2. For removal of transmission without dismantle of the engine execute the following operations.
3. Disconnect the battery from weight.
4. Merge transmission liquid.
5. Lift the car and establish on supports.

7.17 Отворачивание болтов гидротрансформатора
7.17 Otvorachivaniye of hydrotransformer bolts


7.25 Выборка на гидротрансформаторе, которую надо совместить с выступом на насосе
7.25 Selection on the hydrotransformer which should be combined with a ledge on the pump


6. Remove the driveshaft (Hl. 8) also muffle an opening in transmission.
7. Remove a forward exhaust pipe.
8. Disconnect the socket from the blocking switch.
9. Disconnect the socket from the coil the electric drive; kick-down - the mode.
10. Disconnect a vacuum hose from a diaphragm (is directly in front of the electric drive coil).
11. Disconnect draft from the selector.
12. On a shaft of a case of transmission disconnect a speedometer cable.
13. Disconnect a filling branch pipe and muffle an opening in transmission.
14. On a shaft of a case of transmission disconnect cooler hoses.
15. Establish a support under the engine pallet and prop up through whetstone.
16. Uncover and designate a relative positioning of a drive plate and the hydrotransformer.
17. Slowly turning the crankshaft, turn off in turn 4 bolts of fastening of the hydrotransformer.
18. Remove a starter.
19. Drive under transmission the cart with a support and prop up a case.
20. Turn off bolts of fastening of an arm of a support to transmission.
21. Remove an arm from a body.
22. Turn off bolts of fastening of transmission to the engine.
23. Lower both supports so that transmission could be separated and removed in the direction to a back part of the car. It is recommended to remove transmission together.
Take transmission to repare or replace.

7.24 Проверка биения ведущего диска. Если биение не соответствует норме, то диск замените
7.24 Check of a beating of a drive plate. If the beating does not meet standard, then replace a disk


7.27 Проверка установочного размера А гидротрансформатора
7.27 Check of the adjusting size A of the hydrotransformer


24. Check a beating of a drive plate (photo).
25. Installation is carried out upside-down. Combine selection on the hydrotransformer with a ledge on the pump of transmission liquid (photo).
26. Combine the tags on a drive plate and the hydrotransformer put when dismantling.
27. After installation of the hydrotransformer check the size A (photo) to be convinced of the correct installation of the hydrotransformer.
28. Tighten all bolts with the set moment.
29. Turn a drive plate and be convinced of smoothness of rotation of details of transmission.
30. Fill in liquid.
31. Check operation of all switches and draft of management of transmission. If necessary adjust.

"previous page
11.7. A back epiploon - replacement
following page"
12. Coupling driveshaft and back bridge




9ac83ee2