Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The damping cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Coupling mechanism details - removal, dismantling and installation
12.9. The release bearing - replacement
12:10. The directing plug of a main shaft of the check point - replacement
12:11. The driveshaft, a reducer and the back bridge - general information
12:12. Cardan
12:13. An average support - replacement
12:14. Cardan hinges - replacement
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.
12:16. A reducer of the back bridge - removal and installation
12:17. An epiploon of the leading gear wheel of a reducer - replacement
12:18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

12-13-srednyaya-opora-zamena.html

12:13. An average support - replacement

1. Turn off two nuts of an arm of a support, remove both half of an arm.
2. Designate a relative positioning of flanges of forward and back sections of the driveshaft (photo).

11.2 Перед отсоединением карданного вала обозначьте взаимное положение фланцев
11.2 Before a detachment of the driveshaft designate the mutual provision of flanges


12.2 Обозначение взаимного расположения фланцев секций вала
12.2 Designation of a relative positioning of flanges of sections of a shaft


12.3 Зафиксируйте карданный вал и отверните болты фланцев передней и задней секций
12.3 Fix the driveshaft and turn off bolts of flanges of forward and back sections


12.5а Гайка фланца законтрена вдавливанием венца в паз резьбовой части вала
12:5á The Nut of a flange of a zakontren cave-in of a wreath in a groove of a carving part of a shaft


3. Fix the driveshaft and turn off bolts of flanges of forward and back sections (photo).
4. Designate the provision of a flange concerning a groove on a carving part of a shaft.
5. Turn off a nut of a flange of the cardan hinge for what correct раскерненнуго a part of a wreath of a nut (photo), screw bolts in a flange and record shaft section from a provorachivaniye (photo). 6. Remove a flange (photo).
7. Remove an average support by means of a hydraulic press (to vypressovat an average support and it is recommended to press new in car service).
8. At a zapressovyvaniye of an average support, be convinced that the letter "Р is turned to a forward part of the car.
9. Apply a thin film of jellied lubricant on an end face of an average support and a washer. Establish a washer into place.
10. Combine a flange tag with a groove. Establish a flange.
11. Wrap a lock-nut and tighten with the set moment, then a zakontrita, having pressed a nut wreath into a groove of a carving part of a shaft (photo).
12. Combine tags on flanges and wrap bolts.
13. Further operations on assembly are carried out upside-down. At installation of an arm of an average support keep in mind that the joint in a rubber pillow of the bearing of a support has to be turned up.

12.11 Два типа гаек фланца средней опоры – с буртиком (слева), стандартная гайка с шайбой  (справа)
12:11 Two types of nuts of a flange of an average support – with a fillet (at the left), a standard nut with a washer (on the right)


12.5б Отворачивание гайки фланца
12:5í Otvorachivany nuts of a flange


12.6 Снятие фланца средней опоры с переднего карданного вала
12.6 Removal of a flange of an average support from the forward driveshaft



"previous page
12:12. Cardan
following page"
12:14. Cardan hinges - replacement