Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The damping cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Coupling mechanism details - removal, dismantling and installation
12.9. The release bearing - replacement
12:10. The directing plug of a main shaft of the check point - replacement
12:11. The driveshaft, a reducer and the back bridge - general information
12:12. Cardan
12:13. An average support - replacement
12:14. Cardan hinges - replacement
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.
12:16. A reducer of the back bridge - removal and installation
12:17. An epiploon of the leading gear wheel of a reducer - replacement
12:18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





12-14-kardannye-sharniry-zamena.html

12:14. Cardan hinges - replacement

Attention!
Cardan hinges on a part of cars are not subject to replacement. Before dismantling cardan a shaft consult at the supplier of spare parts.

Lock rings of bearings of crosspieces are picked up for thickness. Not to break balancing of the driveshaft new lock rings of crosspieces have to be just the same thickness, as replaced (see. "Specifications")

13.2 Чтобы снять стопорное кольцо, выбейте егс ударами молотка по отвертке
13.2 To remove a lock ring, beat out егс blows of the hammer to the screw-driver


13.3 Выпрессовывание подшипников крестовины
13.3 Vypressovyvaniye of crosspiece bearings


14.6а Полуось и задний мост 1 .  Сальник 2. Гайка колесного подшипника 3. Стопорная шайба колесного подшипника 4. Шайба 5. Колесный подшипник 6. Разделительная втулка 7. Обойма подшипника 8. Сальник 9. Полуось 10. Заправочное отверстие 11. Сапун 12. Сливн
14:6á Half shaft and back bridge 1. Epiploon 2. Nut of the wheel bearing 3. Lock washer of the wheel bearing 4. Washer 5. Wheel bearing 6. Dividing plug 7. Bearing 8 holder. Epiploon 9. Half shaft 10. Filling opening 11. Sapun 12. Slivn


13.6 Установка стопорных колец
13.6 Installation of lock rings


1. Designate a relative positioning of all details of hinges.
2. Clear a fork of dirt and get lock rings (photo).
3. Beat out bearings of crosspieces blows of the hammer with soft brisk on a fork (photo).
4. Get a crosspiece.
5. Check a side play of bearings in necks of crosspieces, replace worn-out details.
6. Assembly is carried out upside-down.

Attention!
Before installation grease lock rings with jellied lubricant Establish lock rings on former places (photo), considering that thickness of lock rings opposite bearings should not differ more than on 0,06 mm.


"previous page
12:13. An average support - replacement
following page"
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.




9ac83ee2