Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The damping cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Coupling mechanism details - removal, dismantling and installation
12.9. The release bearing - replacement
12:10. The directing plug of a main shaft of the check point - replacement
12:11. The driveshaft, a reducer and the back bridge - general information
12:12. Cardan
12:13. An average support - replacement
12:14. Cardan hinges - replacement
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.
12:16. A reducer of the back bridge - removal and installation
12:17. An epiploon of the leading gear wheel of a reducer - replacement
12:18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





12-15-poluos-zadnijj-kolesnyjj-podshipnik-i-salnik-snyatie-i-ustanovka.html

12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.

Removal
1. Lift a back part of the car.
2. Remove wheels.
3. Remove the brake drum (Gl.10)
4. Disconnect a cable of the parking brake and the highway of a hydraulic actuator (Gl.10)
5. Turn off brake board nuts.
6. Remove a half shaft assembled with a brake (photo). If by hand it is not possible to get a half shaft, then it is necessary to use a shock stripper with an adapter which is established on hairpins of fastening of a wheel.
7. Hook and get an external epiploon (photo). An epiploon it is necessary to change every time at removal of a half shaft. Press a new epiploon a mandrel of suitable diameter.
8. Press the bearing from a half shaft. This operation is recommended to be carried out in car service as the stripper or a press is necessary. If these prisposoleniye are available, then execute the following.

14.6б Снятие задней полуоси с помощью ударного съемника
14:6í Removal of a back half shaft by means of a shock stripper


14.9 Расконтрите гайку подшипника заднего колеса, для чего отогните зубцы шайбы
14.9 Raskontrite a nut of the bearing of a back wheel for what unbend washer teeth


9. Unbend teeth of a lock washer of a nut of the bearing (photo).
10. Turn off a bearing nut a vorotkovy key (photo) for what clamp a half shaft in a vice through a soft pro-rate.
11. By means of a press or a stripper remove a half shaft from the bearing and a brake board.
12. Beat out an epiploon from the bearing feedwell (the epiploon is subject to replacement).
13. If on an external holder of the bearing there are damages, then replace the bearing. For this purpose beat out a holder from the feedwell by means of brass a small beard (photo).

14.13 Удаление наружной обоймы подшипника
14:13 Removal of an external holder of the bearing


14.7 Извлечение сальника
14.7 Extraction of an epiploon


14.10 Отворачивание гайки подшипника заднего колеса
14:10 Otvorachivany nuts of the bearing of a back wheel


Installation
14. A mandrel of suitable diameter press a new epiploon of the bearing in the feedwell. Grease working edges of an epiploon with jellied lubricant.
15. Carefully press an external holder of the bearing blows of the hammer to a brass mandrel.
16. Install on a half shaft the dividing plug so,' that the facet on an opening was turned towards a flange of a half shaft (photo).
17. By means of a brass mandrel carefully press the bearing.
18. Establish ring and lock washers, correctly orient and wrap a bearing nut.
19. Zakontrite a nut, having bent teeth of a lock washer.

14.16 Ориентация разделительной втулки подшипника при монтаже на полуось 1. Фланец полуоси 2. Втулка
14:16 Orientation of the dividing plug of the bearing at installation on a half shaft 1. Flange of a half shaft 2. Plug


14.22 Регулировочные прокладки устанавливаются   между торцом балки заднего моста и корпусом подшипника и обеспечивают необходимый продольный люфт полуоси
14:22 Adjusting laying is established  between an end face of a beam of the back bridge and the case of the bearing and provides a necessary longitudinal side play of a half shaft


20. Apply jellied lubricant on the bearing and in a pro-point at an end face of a beam of the back bridge.
21. Oil half shaft vents gearbox, apply jellied lubricant on working edges of an epiploon.
22. Establish all removed adjusting laying (photo).
23. If both half shafts were removed, establish one of them. Measure a longitudinal side play of a half shaft (photo) which has to be 0,3-0,9 mm. If the side play does not meet standard, then adjust for what remove a half shaft and add or remove adjusting laying (thickness of laying is specified Specifications).
24. Establish the second half shaft (if acted) and adjust a side play selection of laying.
25. Further assembly is carried out upside-down.

15.5 Отворачивание болтов редуктора заднего моста
15.5 Otvorachivaniye of bolts of a reducer of the back bridge


14. 23 Проверка продольного люфта полуоси
14. 23 Check of a longitudinal side play of a half shaft



"previous page
12:14. Cardan hinges - replacement
following page"
12:16. A reducer of the back bridge - removal and installation




9ac83ee2