Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The damping cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Coupling mechanism details - removal, dismantling and installation
12.9. The release bearing - replacement
12:10. The directing plug of a main shaft of the check point - replacement
12:11. The driveshaft, a reducer and the back bridge - general information
12:12. Cardan
12:13. An average support - replacement
12:14. Cardan hinges - replacement
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.
12:16. A reducer of the back bridge - removal and installation
12:17. An epiploon of the leading gear wheel of a reducer - replacement
12:18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





12-17-salnik-vedushhejj-shesterni-reduktora-zamena.html

12:17. An epiploon of the leading gear wheel of a reducer - replacement

1. Merge oil from a reducer.
2. Lift a back part of the car, we will establish supports under a frame and a case of a reducer.
3. Disconnect the driveshaft from a reducer and displace aside.
4. Record a reducer flange mount or the big screw-driver, having screwed bolts, and turn off a nut of the leading gear wheel.
5. Remove a flange of a reducer (photo).
6. Hook and remove an epiploon (photo).
7. Grease an epiploon and a pro-point in a case a reducer! jellied lubricant. Accurately, without allowing a smeshcheiya of the leading gear wheel of a reducer, press a new epiploon; so that its surface became aflush with a case (sponges of an epiploon have to be turned inside).

16.5 Снятие фланца редуктора с помощью съемника
16.5 Removal of a flange of a reducer by means of a stripper


8. Establish a reducer flange, a persistent washer and wrap a nut.
9. Having recorded a reducer flange, tighten a nut before disappearance of an axial side play of the leading gear wheel.
10. Turn the leading gear wheel of a reducer several times in both directions. By means of a dynamometer key with a scale in m also measure torque size in several N. at which the leading gear wheel begins to be turned. This moment is equal to a preliminary tightness in bearings of the leading gear wheel and has to correspond specified in Specifications. If the moment appears less demanded, then tighten a reducer nut until the necessary moment is reached.

16.6 Извлечение сальника редуктора
16.6 Extraction of an epiploon of a reducer


Attention!
The preliminary tightness is provided with the expansion plug of bearings of the leading gear wheel. If the size of a preliminary tightness is more recommended, then the plug will be deformed. In this case the reducer should be removed and replaced the expansion plug.

17.8 Задний мост (стрелками указаны разбираемые соединения при снятии моста)
17.8 Zadny Bridge (shooters specified the investigated connections at removal of the bridge)


11. Further assembly is carried out upside-down.
12. Upon termination of fill in oil in a reducer.

"previous page
12:16. A reducer of the back bridge - removal and installation
following page"
12:18. Zadny Bridge - removal and installation