Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The damping cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Coupling mechanism details - removal, dismantling and installation
12.9. The release bearing - replacement
12:10. The directing plug of a main shaft of the check point - replacement
12:11. The driveshaft, a reducer and the back bridge - general information
12:12. Cardan
12:13. An average support - replacement
12:14. Cardan hinges - replacement
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.
12:16. A reducer of the back bridge - removal and installation
12:17. An epiploon of the leading gear wheel of a reducer - replacement
12:18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





12-8-detali-mekhanizma-scepleniya-snyatie-razborka-i-ustanovka.html

12.8. Coupling mechanism details - removal, dismantling and installation

1. The increased noise (gnash) at inclusion of transfers or pro-slipping of coupling confirm strong wear of a frictional disk.
2. Wear of coupling strongly depends on a manner of driving of Probuksovk when driving will accelerate wear of a frictional disk the Frictional disk is recommended to be changed through each 64000 km of a run.
3. For access to coupling it is necessary to remove the transmission (Hl. 7).
4. After removal of the check point examine coupling outside and check a condition of fingers of a diaphragm spring on a coupling casing. At detection of any damages (deformation or a bend of fingers) replace a coupling casing assembled with a spring.
5. Gradually, in the diagonal sequence release bolts, stress of a spring (photo) will not be removed yet. Do not damage a press plate. Record a flywheel from a provorachivaniye, having inserted the screw-driver into a starter aperture.
6. Turn out bolts, remove a casing of coupling, press a disk and a frictional disk. (photo)
7. Clear of lubricant and dirt press a disk, a flywheel and the holder of the bearing.
8. Check a condition of a surface of a press disk existence on it of zadir, dents and scratches. Check a condition of petals of a diaphragm spring and dead Check deformation of petals by means of the probe (unevenness of petals on height, a photo), be convinced that this size does not exceed the limit specified in Specifications. At detection of any defects assembled replace coupling.

7.14 Перед затягиванием болтов сцентрируйте фрикционный диск относительно маховика
7.14 Before tightening of bolts center a frictional disk concerning a flywheel


8.4 Отсоединение пружины шаровой опоры вилки выключения сцепления
8.4 Detachment of a spring of a spherical support of a fork of switching off of coupling


9. Check wear of a frictional disk. Replace a disk if distance from a surface of a frictional slip to heads of rivets less than 0,8 mm or if on frictional material there are any damages or oil spots.

8. 6 Снятие выжимного подшипника
8. 6 Removal of the release bearing


10. Check a condition of a surface of a flywheel. If on it there are superficial damages, then a proshlifuyta a flywheel. At considerable damages (breakages on a gear wreath, burning out traces on a frictional surface) replace a flywheel (Hl. 2).
11. If on details of coupling oil traces are found, then establish the reason and eliminate. If oil is revealed from a coupling casing, then replace an epiploon of a main shaft of the check point.
12. The release bearing is recommended to be replaced. Check wear of the directing bearing plug, if necessary replace (see below).
13. Before assembly apply a thin film of molybdenic lubricant on vents of a main shaft.
14. Before installation of coupling center a frictional disk concerning a flywheel by means of a mandrel or the suitable tool (photo).
15. Install a coupling basket on the directing pins. Wrap bolts and tighten in the diagonal sequence in several stages before achievement of the set moment (photo).
16. Install the transmission.

"previous page
12.7. A coupling hydraulic actuator - removal
following page"
12.9. The release bearing - replacement




9ac83ee2