Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
12.1. Specifications
12.2. Coupling - general information
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The damping cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydraulic actuator - removal
12.8. Coupling mechanism details - removal, dismantling and installation
12.9. The release bearing - replacement
12:10. The directing plug of a main shaft of the check point - replacement
12:11. The driveshaft, a reducer and the back bridge - general information
12:12. Cardan
12:13. An average support - replacement
12:14. Cardan hinges - replacement
12:15. A half shaft, the back wheel bearing and an epiploon - removal and installation.
12:16. A reducer of the back bridge - removal and installation
12:17. An epiploon of the leading gear wheel of a reducer - replacement
12:18. Zadny Bridge - removal and installation
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





12-9-vyzhimnojj-podshipnik-zamena.html

12.9. The release bearing - replacement

1. At repair or replacement of details of coupling it is necessary to replace the release bearing, or to perform works on its service.
2. If a lubricant exit from the bearing is observed, or the bearing is hardly turned by hand, then it should be replaced.
3. Remove a rubber cover of a clutch release fork lever.
4. Disconnect the screw-driver a spring of a spherical support of a fork (photo).
5. Remove a coupling switching off fork.
6. Remove the release bearing (photo).

Attention!
Check existence on a fork of cracks and deformations. Check freedom of rotation of the bearing by hand. The release bearing cannot be washed out and in solvent. At installation of new coupling the release bearing should be replaced.

7. If necessary press the release bearing from a nave (photo).

8.7 Выпрессовывание выжимного подшипника со ступицы
8.7 Vypressovyvaniye of the release bearing from a nave


8.9 Заложите смазку во внутреннюю полость ступицы, смажьте места, указанные стрелками 1.  Заложить смазку
8.9 Put lubricant in an internal cavity of a nave, grease the places specified by arrows 1. To put lubricant


9.5 Удаление направляющей втулки специальным съемником
9.5 Removal of the directing plug a special stripper


8. Press the new bearing, putting effort to an external holder.
9. Assembly is carried out upside-down. Put refractory lubricant in an internal cavity of a nave (photo).
10. Apply a thin film of the same lubricant on the rubbing fork surfaces. Excess lubricant is not allowed
11. At installation of a fork on the release bearing be convinced that the terminations of a spring came into a pro-point of the bearing and rest against a fork (photo).

9.6 Удаление направляющей втулки гидроударом
9.6 Removal of the directing plug hydroblow


8.11  Фиксация выжимного подшипника пружиной на вилке выключения сцепления
8.11 Fixing of the release bearing a spring on a coupling switching off fork



"previous page
12.8. Coupling mechanism details - removal, dismantling and installation
following page"
12:10. The directing plug of a main shaft of the check point - replacement




9ac83ee2