Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
13.1. Specifications
13.2. General information
13.3. The nave automatic interlock device - removal and installation
13.4. Half shafts - removal and installation
13.5. A half shaft - dismantling and assembly
13.6. A nave and a rotary fist - smyaty and installation
13.7. Nave epiploons – removal and installation, adjustment of bearings
13.8. The forward driveshaft - removal and installation
13.9. Epiploons of a forward reducer - replacement
13:10. A forward reducer - removal and installation
13:11. Epiploons of the transfer case - replacement
13:12. The transfer case - removal and installation
13:13. The transfer case - dismantling
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

13-5-poluos-razborka-i-sborka.html

13.5. A half shaft - dismantling and assembly

1. Remove a half shaft.
2. Clamp a half shaft in a vice through soft laying.

2.5 Проверка толщины блокирующих колец L (должна быть не менее 15,4 мм).
2.5 Check of thickness of the blocking rings of L (there have to be not less than 15,4 mm).


3.11 Удаление полуоси из поворотного кулака 1.  Брусок
3.11 Removal of a half shaft from a rotary fist 1. Whetstone


3.13 Проверка осевого люфта полуоси
3.13 Check of an axial side play of a half shaft


4.3 Разборка внутреннего шарнира
4.3 Dismantling of the internal hinge


4.4 Детали полуоси 1.  Со стороны колеса 2. Детали ШРУСа типа Rzeppa  3,7,16. Стопорное кольцо 4. Вал 5.  Шарнир типа Tripod (
4.4 Details of a half shaft 1. From a wheel 2. Details of the Rzeppa 3,7,16 CV JOINT. Lock ring 4. Shaft 5. The Tripod hinge (the "sliding" hinge) 6. Cap 8. Crosspiece 9. Case 10,13. Cover 11,12,14, Collar 15. Hinge 17. The ring is selected on thicknesses


3. Carefully bring down a half shaft flange from differential and release a cap of the case of the hinge (photo).
4. Remove collars of covers (photo).
5. Displace covers and the case of the sliding hinge towards a wheel pin.
6. Designate the provision of a crosspiece on a half shaft shaft.
7. Vypressuyte a half shaft from a crosspiece (it is carried out on the press).
8. Remove a cover and the case.
9. Designate situation on a half shaft and carefully beat out the external CV JOINT (photo), remove a lock ring.
10. Wash out and examine all details.
11. Before assembly put lubricant in the external CV JOINT.
12. Dress a cover on a half shaft and establish a new lock ring. Put lubricant in the external CV JOINT and fix a cover by collars.
13. Dress a cover on a half shaft from differential, collars and install the case of the internal CV JOINT.
14. Clamp a half shaft in a vice and establish a crosspiece so that the gear collar of a crosspiece was turned towards a half shaft.

Attention!
If the removed crosspiece is established, then combine the tags put when dismantling. If the new crosspiece is established, then displace a crosspiece towards a pin to a limit.

15. Record a crosspiece on a shaft, расклепав a gear collar in two places (photo). Rasklepka depth not less than 1 mm.

4.9 Удаление наружного ШРУСа с полуоси
4.9 Removal of the external CV JOINT from a half shaft


4.12 При установке чехла выдержите размер L
4.12 At installation of a cover sustain the size L


4.15 Фиксация крестовины скользящего  ШРУСа  на валу полуоси, 1. Не менее 1 мм
4.15 Fixing of a crosspiece of the sliding CV JOINT on a half shaft shaft, 1. Not less than 1 mm


16. Dress the case and put lubricant in the internal CV JOINT
17. Fix a cover by a new collar.
18. Apply lubricant on an epiploon of a cap and establish a cap, screw three bolts and a nut. Vpressuyte a cap, I will hit in three places.
19. Establish the size L of a cover (photo) and level a cover, having removed residual pressure. Fix by a small collar.


"previous page
13.4. Half shafts - removal and installation
following page"
13.6. A nave and a rotary fist - smyaty and installation