Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
13.1. Specifications
13.2. General information
13.3. The nave automatic interlock device - removal and installation
13.4. Half shafts - removal and installation
13.5. A half shaft - dismantling and assembly
13.6. A nave and a rotary fist - smyaty and installation
13.7. Nave epiploons – removal and installation, adjustment of bearings
13.8. The forward driveshaft - removal and installation
13.9. Epiploons of a forward reducer - replacement
13:10. A forward reducer - removal and installation
13:11. Epiploons of the transfer case - replacement
13:12. The transfer case - removal and installation
13:13. The transfer case - dismantling
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

13-7-salniki-stupicy-snyatie-i-ustanovka-regulirovka-podshipnikov.html

13.7. Nave epiploons – removal and installation, adjustment of bearings

1. Remove a nave and a fist.
2. Unscrew the screw of a lock plate.
3. Turn off a lock-nut, record a nave (photo).
4. Remove a plate and a special washer (photo).
5. Hook and get a maslootrazhatel, push out the bearing plug.
6. Remove a fist (photo).
6.b Removal of a fist from a nave
7. Get a bearing cuff
8. Vypressuyte ring of the internal bearing (photo)
9. Turn off bolts and remove a nave from a brake disk (Hl. 10).
10. Vypressuyte the external bearing by means of a press, remove a maslootrazhatel.
11. Wash out all details.

6.3 Фиксация ступицы при отворачивании гайки
6.3 Fixing of a nave at a nut otvorachivaniye


5.6б Болты нижней опоры
5.6b Bolts of the lower support


6.4 Ступица, полуось и   поворотный кулак 1. Диск  тормоза 2. Сальник А 3. Внутренний подшипник 4. Наружный подшипник 5. Контргайка 6. Стопорная пластина  7. Поводковая муфта 8,10 Стопорное кольцо 9. Устройство для ручной блокировки ступицы (а/м ранних вы
6.4 Nave, half shaft and  rotary fist 1. Disk of a brake 2. Epiploon A 3. Internal bearing 4. External bearing 5. Lock-nut 6. Lock plate 7. Povodkovy coupling 8,10 Lock ring 9. The device for manual blocking of a nave (the car early you


6.8 Выпрессовка кольца внутреннего подшипника 1.  Латунный бородок
6.8 Vypressovka of a ring of the internal bearing 1. Brass small beards


12. Grease a holder of the external bearing, put lubricant in a nave (photo) and press in the bearing in a nave, resting against an external ring. Fill with lubricant the central space of a nave. Establish an external epiploon.
13. Establish a disk.
14. Grease and press the internal bearing.
15. Tighten a nave nut with the set moment.
16. Check freedom of rotation of a nave.
17. Grease and establish an internal epiploon

Adjustment

Attention!
The special key is applied to an otvorachivaniye and an inhaling of a nut (Hl. 8)

18. Tighten a nut with the set moment.
19. Release a nut and check a side play which has to be equal to zero.

6.12 Заложите смазку в места указанные штриховкой
6.12 Put lubricant to the places specified by shading


20. Turn a wheel in both directions.
21. Define a preliminary tightness in bearings. For this purpose, having hooked on a dynamometer for the top hairpin, define effort And under which the wheel will begin to rotate. Further tighten a nut on 15-30 ° and establish a lock plate on a nut. Turn a wheel in both directions. Hook on a dynamometer for the lower hairpin define effort In under which the wheel will begin to rotate. The tightness is equal to a difference V-and.
22. Repeat the procedure and achieve a normal tightness in bearings.
23. Establish a lock ring in a nut flute.
24. Establish other details upside-down.


"previous page
13.6. A nave and a rotary fist - smyaty and installation
following page"
13.8. The forward driveshaft - removal and installation