Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
13.1. Specifications
13.2. General information
13.3. The nave automatic interlock device - removal and installation
13.4. Half shafts - removal and installation
13.5. A half shaft - dismantling and assembly
13.6. A nave and a rotary fist - smyaty and installation
13.7. Nave epiploons – removal and installation, adjustment of bearings
13.8. The forward driveshaft - removal and installation
13.9. Epiploons of a forward reducer - replacement
13:10. A forward reducer - removal and installation
13:11. Epiploons of the transfer case - replacement
13:12. The transfer case - removal and installation
13:13. The transfer case - dismantling
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





13-9-salniki-perednego-reduktora-zamena.html

13.9. Epiploons of a forward reducer - replacement

Epiploon of the leading gear wheel of the main transfer
1. Merge oil from a reducer case
2. Lift a front of the car and establish on supports.
3. Disconnect the driveshaft from a flange of a forward reducer.
4. Turn off a nut of a reducer (photo), having screwed bolts in a flange and having rested the screw-driver.
5. Press a flange of a reducer (photo).
6. Hook and accurately get an epiploon.
7. Put universal lubricant in an epiploon and press in a case a mandrel.
8. Dress a flange, turn and tighten a reducer nut with the set moment.
9. By means of a dynamometer key with a scale of m check the moment of resistance to a provorachivaniye of the leading gear wheel of a reducer for several N., having turned for a nut clockwise. The moment is equal to a preliminary tightness in bearings. If the moment is less than norm, then tighten a nut. If the moment exceeds norm, then the expansion plug of bearings will be damaged, the reducer should be sorted and replaced the plug.

8.5 Снятие фланца с ведущей шестерни главной передачи
8.5 Removal of a flange from the leading gear wheel of the main transfer


8.12 Снятие фланца полуоси
8.12 Removal of a flange of a half shaft


10. Other operations are carried out upside-down.
Epiploon of the left half shaft
11. Remove a half shaft.
12. Remove a half shaft flange, having hooked two screw-drivers (photo).
13. Get an epiploon.
14. Press a new epiploon.
15. Put universal lubricant in an epiploon and press in a case a mandrel.
16. Establish a flange and a half shaft.
Right epiploon
17. Turn off 4 bolts of fastening of the case of the bearing and the right shaft of a reducer (photo).
18. Clamp a half shaft in a vice, having laid wooden whetstones.
19. Carefully cut down the plug from a shaft (photo).

8.17 Детали правой части переднего редуктора 1.  Регулировочная прокладка 2. Корпус подшипника 3. Сальник 4. Кольцо 5. Правый вал 6. Подшипник 7. Втулка 8. Корпус
8.17 Details of the right part of a forward reducer 1. Adjusting laying 2. Bearing 3 case. Epiploon 4. Ring 5. Right shaft 6. Bearing 7. Plug 8. Case


8.19 Удаление втулки подшипника с правого вала
8.19 Removal of the plug of the bearing from the right shaft


8.21 Выпрессовка вала 1.  Втулка удалена
8.21 Vypressovka of a shaft 1. The plug is removed


9.6 Болты крепления переднего редуктора
9.6 Bolts of fastening of a forward reducer


9.8 Болты крепления редуктора к раме.
9.8 Bolts of fastening of a reducer to a frame.


20. Turn off 4 bolts and remove the case of the right shaft from a reducer.
21. Install a half shaft in the case, tighten the case of the bearing and a vypressuyta a shaft from the bearing (photo).
22. Hook and get an epiploon from the bearing case. Press a new epiploon blows through whetstone.
23. Remove the case of the bearing and dress on a shaft. Dress the new plug. Press a shaft in the case (it is recommended to execute in car service).
24. Other operations are carried out upside-down.

"previous page
13.8. The forward driveshaft - removal and installation
following page"
13:10. A forward reducer - removal and installation




9ac83ee2