Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum brakes - replacement of blocks
14.7. The wheel cylinder of back drum brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14:10. Blocks of the emergency brake (on back disk brakes) - removal, installation and adjustment
14:11. The main cylinder of brakes - removal, dismantling and installation
14:12. The regulator of pressure of brakes - removal and installation
14:13. The highway of a hydraulic actuator - check and replacement
14:14. Pumping of brakes
14:15. The vacuum amplifier of brakes - general information and check
14:16. The vacuum amplifier of brakes - removal and installation
14:17. The emergency brake - adjustment
14:18. The lever of the emergency brake - removal and installation
14:19. Cables of the emergency brake - removal and installation
14:20. The braking signal switch - removal and installation
14:21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





14-10-kolodki-ruchnogo-tormoza-na-zadnikh-diskovykh-tormozakh.html

14:10. Blocks of the emergency brake (on back disk brakes) - removal, installation and adjustment

Removal
1. Remove a disk of a back brake.
2. Remove clamping springs of blocks for what press a cap and turn on 90 ° (photo).
3. Displace blocks from a board of a brake (photo), remove two springs, a guide and a strut.
4. Part blocks in the top part and remove from a half shaft flange, disconnect a cable of the emergency brake from the lever
5. Remove a spring and the regulator, wash out details in solvent and grease a carving part with jellied lubricant.
6. If blocks change, then install the conducted lever of the emergency brake on a new block.

9.2 Детали ручного тормоза задних дисковых тормозов 1. Пальцы прижимных пружин 2. Щит тормоза 3. Регулятор 4. Регулировочная пружина 5. Контактные поверхности 6. Опорная шайба 7. Пружина 8. Колпачок прижимной пружины 9. Пружина 10. Распорка 11.  возвратны
9.2 Details of the emergency brake of back disk brakes 1. Fingers of clamping springs 2. Board of a brake 3. Regulator 4. Adjusting spring 5. Contact surfaces 6. Basic washer 7. Spring 8. Cap of a clamping spring 9. Spring 10. Strut 11. vozvratna


9.3 Освободите колодки, подайте на себя  и  снимите возвратные пружины
9.3 Release blocks, give on yourself and remove returnable springs


Installation
7. Hook on a regulator spring for a block and install the regulator. Make sure that grooves on the regulator came into end faces of blocks.
8. Slightly grease those places of blocks which adjoin to a board of a brake (photo).
9. Attach a cable to the lever on a block.
10. Part blocks and establish, having pressed to a brake board. Establish a strut.
11. Establish clamping springs of blocks, fix by caps, having turned them on 90 °.
12. Establish springs and a guide.
13. Establish a disk on a flange of a half shaft and record, having screwed two nuts of a wheel. Install the cylinder and a support.
Adjustment
14. Check that the emergency brake is completely released. Get a cap in a board and having inserted the screw-driver, rotate the regulator for teeth until the block does not adjoin to a drum of a disk (photo).
15. Unscrew the regulator in the opposite direction on 7-8 clicks and be convinced that the disk rotates freely, without touching a block.
16. Put a cap into place.

9.14 Удалите заглушку и отверткой вращайте регулятор за зубцы до тех пор пока колодка не соприкоснется с барабаном диска, затем отверните регулятор в обратную сторону на 7-8 щелчков. 1. Заглушка регулятора  2. Отвертка 3. Отвести колодку
9.14 Remove a cap and the screw-driver rotate the regulator for teeth until the block does not adjoin to a disk drum, then unscrew the regulator in the opposite direction on 7-8 clicks. 1. Regulator 2 cap. Screw-driver 3. To take away a block


9.7  Места смазки на щите тормоза
9.7 Places of lubricant on a brake board




"previous page
14.9. Disks of back brakes - check, removal and installation
following page"
14:11. The main cylinder of brakes - removal, dismantling and installation




9ac83ee2