Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum brakes - replacement of blocks
14.7. The wheel cylinder of back drum brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14:10. Blocks of the emergency brake (on back disk brakes) - removal, installation and adjustment
14:11. The main cylinder of brakes - removal, dismantling and installation
14:12. The regulator of pressure of brakes - removal and installation
14:13. The highway of a hydraulic actuator - check and replacement
14:14. Pumping of brakes
14:15. The vacuum amplifier of brakes - general information and check
14:16. The vacuum amplifier of brakes - removal and installation
14:17. The emergency brake - adjustment
14:18. The lever of the emergency brake - removal and installation
14:19. Cables of the emergency brake - removal and installation
14:20. The braking signal switch - removal and installation
14:21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





14-11-glavnyjj-cilindr-tormozov-snyatie-razborka-i-ustanovka.html

14:11. The main cylinder of brakes - removal, dismantling and installation

1. Disconnect the battery from weight.
2. Substitute the pallet or spread rags.
3. Release the union of tubes on the main cylinder (photo).
4. Turn off nuts of fastening of the cylinder to the vacuum amplifier.
5. Carefully remove the cylinder from hairpins, turn off the union and muffle openings. Get the cylinder.
6. Muffle hydraulic actuator tubes.

Dismantling
7. Prepare ремкомплект the main cylinder.

Attention!
In the main tsilintsr of the considered cars remkomplekta of Nabco and Tokico which are not interchanged are used. Therefore at first get necessary ремкомплект.

8. Clear the cylinder and merge liquid.
9. Remove a cap, get a lock washer (if it is provided, the first piston and a spring (photo).
10. Get the secondary piston, having knocked with the cylinder about wooden whetstone.
11. Check a condition of the cylinder. At detection of scratches or the painted sites replace the cylinder

10.3 Гайки штуцеров на главном цилиндре (рекомендуется отпускать газовым ключом)
10.3 Nuts of unions on the main cylinder (it is recommended to release an alligator wrench)


10.9 Детали главного цилиндра тормозов 1. Пробка 2. Фильтр 3. Поплавок  4.Бачок 5. Вторичный поршень в сборе 6. Первичный поршень 7. Колпачок  8,9- Манжеты 10. Опорная шайба 11. Пружина 12. Цилиндр 13. Уплотнители 14. При сборке смазать жидкостью
10.9 Details of the main cylinder of brakes 1. Stopper 2. Filter 3. Float 4. Tank 5. Secondary piston assembled 6. Primary piston 7. Cap 8,9 Cuffs 10. Basic washer 11. Spring 12. Cylinder 13. Uplotniteli 14. At assembly to grease with liquid



12. Disassemble the secondary piston (primary non-demountable).
13. Wash out all details in alcohol or brake fluid.
14. Remove a tank only if necessary.
15. Dress on the cuff piston, having tracked correctness of their orientation.
16. Dip details into brake fluid.
17. Collect all details as their former installation, bend ears on a cap (photo) and install on the cylinder. If the cap is damaged, then replace it.
Installation
18. Before installation it is recommended to fill the cylinder with liquid and to remove air. This measure will reduce duration of pumping of brakes.
19. Close carving caps of an opening under the union, fix the cylinder and fill with liquid a cylinder tank.
20. Turn off one of caps, press pistons, wrap a cap and release pistons.

10.17 Перед сборкой главного цилиндра загните ушки на колпачке
10:17 Before assembly of the main cylinder bend ears on a cap


11.2а Регулятор давления тормозов типа А 1.  Штуцер  для  прокачки  2. Кронштейн  3. Регулятор давления (неразборньй)
11:2á Regulator of pressure of brakes of the A 1 type. The union for pumping 2. Arm 3. Pressure regulator (неразборньй)


11.2б Регулятор давления тормозов типа В 1.  Штуцер  для  прокачки 2. Регулятор давления (неразборный) 3. Кронштейн 4. Пружина
11:2í Regulator of pressure of brakes of the B 1 type. The union for pumping 2. Pressure regulator (non-demountable) 3. Arm 4. Spring


21. Repeat the procedure for each of openings on 3-4 times.
22. Instead of a cap it is possible to close one of openings a finger. Release a finger after pressing pistons after an effluence of liquid close an opening a finger and release pistons. Several seconds later take away a finger.
Repeat the procedure and perform the same operations on other opening.
23. After only liquid begins to follow from openings wrap caps.
24. Add liquid in a tank before the top division and wrap a stopper.
25. Install the cylinder upside-down and pump over brakes.


"previous page
14:10. Blocks of the emergency brake (on back disk brakes) - removal, installation and adjustment
following page"
14:12. The regulator of pressure of brakes - removal and installation