Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum brakes - replacement of blocks
14.7. The wheel cylinder of back drum brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14:10. Blocks of the emergency brake (on back disk brakes) - removal, installation and adjustment
14:11. The main cylinder of brakes - removal, dismantling and installation
14:12. The regulator of pressure of brakes - removal and installation
14:13. The highway of a hydraulic actuator - check and replacement
14:14. Pumping of brakes
14:15. The vacuum amplifier of brakes - general information and check
14:16. The vacuum amplifier of brakes - removal and installation
14:17. The emergency brake - adjustment
14:18. The lever of the emergency brake - removal and installation
14:19. Cables of the emergency brake - removal and installation
14:20. The braking signal switch - removal and installation
14:21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

14-5-disk-tormoza-proverka-snyatie-i-ustanovka.html

14.5. A brake disk - check, removal and installation

Check
1. Release nuts of wheels, lift the car and establish on supports. Remove wheels.
2. Remove a support with the cylinder and take aside.
3. Check a condition of a disk. At detection of traces of deep development (depth more than 0,38 mm) remove a disk and a proshlifuyta (photo).
4. Check a beating (especially if when braking vibrations were felt) by means of the arrow indicator (photo). If the beating on the indicator exceeds norm, then remove a disk and a proshlifuyta.

Attention!
The disk in general is recommended to be removed and proshlifovyvat periodically on it is dependent on indications of the indicator. At least it can be made by hand a small skin (photo) to reduce a roughness.

5. After grinding thickness of a disk should not be less maximum permissible (thickness is cast on a disk, a photo).
Removal
6. Remove a dustproof cover of a nave.
7. Remove the forelock.

3.12 Установка поршня в цилиндр 1.  Цилиндр  2. Поршень  3. Манжета 4. Чехол
3.12 Installation of the piston in the cylinder 1.  Cylinder 2. Piston 3. Cuff 4. Cover


4.4а Проверка биения диска
4.4a Check of a beating of a disk


8. Remove a cap.
9. Turn off a nut of a nave and remove a washer.
10. Remove the external bearing.
11. Remove a nave assembled with a disk.
12. If the disk pereshlifovyvatsya, then get: epiploon.

4.4б Шлифовка диска от руки
4.4b Grinding of a disk by hand


4.5а Место  нанесения предельной толщины диска
4.5a Place of drawing extreme thickness of a disk


4.13а Болты крепления диска к ступице
4.13a Bolts of fastening of a disk to a nave


13. If the disk changes, then separate it from a nave for what turn off bolts, tap on edge of a nave, hook screw-drivers and remove a disk (photo). If it is not possible to separate a disk in such a way, then grease a joint of a disk and a nave with the getting liquid.
Installation
14. Establish a disk on a nave and screw bolts.
15. Evenly and gradually tighten bolts to the full.
16. Other operations are carried out according to Gl.11.


"previous page
14.4. A brake support - removal, dismantling and installation
following page"
14.6. Back drum brakes - replacement of blocks