Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. General information
14.3. Blocks disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum brakes - replacement of blocks
14.7. The wheel cylinder of back drum brakes - removal, dismantling and installation
14.8. See hl. 1
14.9. Disks of back brakes - check, removal and installation
14:10. Blocks of the emergency brake (on back disk brakes) - removal, installation and adjustment
14:11. The main cylinder of brakes - removal, dismantling and installation
14:12. The regulator of pressure of brakes - removal and installation
14:13. The highway of a hydraulic actuator - check and replacement
14:14. Pumping of brakes
14:15. The vacuum amplifier of brakes - general information and check
14:16. The vacuum amplifier of brakes - removal and installation
14:17. The emergency brake - adjustment
14:18. The lever of the emergency brake - removal and installation
14:19. Cables of the emergency brake - removal and installation
14:20. The braking signal switch - removal and installation
14:21. Anti-blocking system (ABS) - general information and access to codes.
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





14-6-zadnie-barabannye-tormoza-zamena-kolodok.html

14.6. Back drum brakes - replacement of blocks

1. Lift a back part of the car and establish on supports. Release the emergency brake.
2. Remove a wheel.
3. If necessary reduce blocks the regulator (Hl. 1)
4. Remove a drum for what rotating a drum, knock on it with the hammer with soft brisk in the direction outside. If the drum does not give in to removal, then displace it, evenly wrapping bolts of M8 x 1,25 in special carving openings (photo).

4.5б  Проверка толщины диска. Измерьте толщину в нескольких местах
4.5b Check of thickness of a disk. Measure thickness in several places


4.13б Разделение диска и ступицы
4.13b Division of a disk and nave


5.4 Снятие барабана с помощью вспомогательных болтов
5.4 Removal of a drum by means of auxiliary bolts


5. Carefully clear a drum of dust and dirt.
6. Remove clamping springs of blocks for what press a cap and turn on 90 ° (photo).
7. Remove the top coupling springs of blocks (photo).
8. Part blocks and get a strut (photo).

5.6 Снятие прижимных пружин колодок
5.6 Removal of clamping springs of blocks


9. In addition part blocks and get them from grooves in the regulator and pistons. Fix pistons from a vydviganiye from cylinders (that at assembly not to pump over a hydraulic actuator).
10. Disconnect a cable of the emergency brake from the lever.
11. Do not press a pedal of a brake, otherwise pistons will go out of the cylinder.
12. Check a condition of covers of the cylinder and existence of a leak of liquid. If necessary repair or replace cylinders.

5.7б Верхняя пружина, направляющая и трос peгулятора
5.7b Top spring, guide and cable of the regulator


13. Grease a carving of the regulator of blocks brake liquid.
14. Before assembly slightly grease the rubbing places ю boats with brake lubricant, without allowing hit on pi zinovy details.
5.7a Details of a back drum brake of the polnopoivolny car "Terrann I/Pathfinder" 1. Adjusting lever 2. Spring 3. Basic washer of a spring 4. Clamping spring 5. Cap of a spring 6. Reel 7. An adjusting cable with a spring 8,14. Spring 9,12


5.8 Снятие распорки колодок
5.8 Removal of a strut of blocks


5.16 Маркировка с указанием предельного внутреннего диаметра барабана
5.16 Marking with the indication of extreme internal diameter of a drum


15. Establish springs, enter the lower end face of a back block then the lower end face of a forward block into a regulator groove, move apart blocks and enter into grooves of pistons of the wheel cylinder. Establish other details (photo).
16. Install the reel and a wheel.
17. Adjust a gap between blocks and drums having several times lifted and having lowered the lever of the emergency brake. If necessary remove air from brakes. Lower the car.


"previous page
14.5. A brake disk - check, removal and installation
following page"
14.7. The wheel cylinder of back drum brakes - removal, dismantling and installation