Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
15.1. Specifications
15.2. General information
15.3. Hairpins of fastening of a wheel - replacement
15.4. The stabilizer - removal and installation
15.5. Shock-absorbers - removal and installation
15.6. The torsion - removal and installation
15.7. Bars and extensions of a suspension bracket - removal and installation
15.8. The top lever and a spherical support - removal and installation
15.9. The lower lever and a spherical support - removal and installation
15:10. Springs of a back suspension bracket - removal and installation
15:11. Bars of a back suspension bracket - removal and
15:12. The stabilizer of a back suspension bracket - removal and installation
15:13. Steering - general information
15:14. A wheel - removal and installation
15:15. The lock of a steering column - removal and installation
15:16. A steering reducer - removal and installation
15:17. A steering reducer (the car without hydraulic booster) - dismantling
15:18. Steering
15:19. The pump hydraulic boosters - removal and installation
15:20. Removal of air from a wheel hydraulic actuator
15:21. Steering drafts - removal and installation
15:22. The angles of installation of forward wheels - general information
15:23. Wheels and tires - general information
16. Body and elements of finishing
17. System of electric equipment
 





15-21-rulevye-tyagi-snyatie-i-ustanovka.html

15:21. Steering drafts - removal and installation

1. Side drafts, cross draft, a bipod and the pendular lever (photo) belong to steering drafts.
2. All steering drafts can be removed assembled with the pendular lever and a bipod. After dismantle of drafts it is necessary to check the angles of installation of wheels. Finally tighten nuts of tips after lowering of the car.
Side drafts
3. Rasshplintuyte also turn off nuts (photo).

20.3 Детали боковой тяги 1. Наружный наконечник 2. Хомут 3. Резьбовая втулка 4. Внутренний наконечник
20.3 Details of side draft 1. External tip 2. Collar 3. Carving plug 4. Internal tip


4. Vypressuyte fingers of tips of drafts a special stripper (photo) also get draft.
5. Check a side play in spherical fingers, if necessary replace fingers.
6. If necessary sort drafts for what designate the provision of tips in the plug, turn off bolts of collars and turn out both tips.
7. Assembly and installation are carried out upside-down. If the removed tips are established, then combine the tags put before dismantling. If new drafts are established, then expose the size A on the removed drafts (photo). After assembly check and adjust the angles of installation of wheels.

20.9 Детали маятникового рычага1. Чехол2. Кронштейн3,6. Втулка4.Мзятниковый  рычаг5. Заглушка масленки7. Шайба8. Гайка
20.9 Details of the pendular lever
1. Cover
2. Arm
3,6. Plug
4. Mzyatnikovy lever
5. Butterdish cap
7. Washer
8. Nut


20.4 Выпрессовывание пальца наконечника
20.4 Vypressovyvaniye of a tip finger


20.7  Размер А, который надо выставить на новых тягах
20.7 The size A which should be exposed on new drafts


20.10 Маятниковый рычаг
20:10 Pendular lever


21.1 Углы установки передних колес1. Вертикаль2. Линия параллельная оси симметрии автомобиля3.Развал4. Ось шаровых опор подвески5. Продольный угол наклона оси поворота6. Схождение колес
21.1 Angles of installation of forward wheels
1. Vertical
2. Line parallel to an axis of symmetry of the car 
3. Disorder
4. Axis of spherical support of a suspension bracket
5. Longitudinal tilt angle of an axis of turn 
6. Convergence of wheels


22.1 Маркировка шин
22.1 Marking of tires


Pendular lever
8. The side play in the pendular lever is eliminated with installation of new plugs.
9. Turn off bolts of fastening of an arm of the lever to a frame (photo).
10. Rasshplintuyte also turn off a nut, a vypressuyta a finger of the pendular lever from cross draft (photo).
11. If it is necessary to replace plugs, then turn off a nut, remove a washer and remove the lever from an arm, get plugs. Replace plugs and collect the lever.
12. Installation is carried out upside-down. Tighten all nuts with the set moment.
Cross draft
13. Rasshplintuyte also turn off all nuts of cross draft.
14. Vypressuyte fingers also get draft.
15. Check a condition of plugs of draft, if necessary replace.
16. Installation is carried out upside-down.
Drafts of steering assembled
17. Turn off a nut of a bipod and press a bipod from a reducer shaft.
18. Turn off bolts and remove the pendular lever.
19. Rasshplintuyte also turn off nuts of side drafts on rotary fists, a vypressuyta fingers.
20. Remove all drafts.
21. Installation is carried out upside-down


"previous page
15:20. Removal of air from a wheel hydraulic actuator
following page"
15:22. The angles of installation of forward wheels - general information