Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
15.1. Specifications
15.2. General information
15.3. Hairpins of fastening of a wheel - replacement
15.4. The stabilizer - removal and installation
15.5. Shock-absorbers - removal and installation
15.6. The torsion - removal and installation
15.7. Bars and extensions of a suspension bracket - removal and installation
15.8. The top lever and a spherical support - removal and installation
15.9. The lower lever and a spherical support - removal and installation
15:10. Springs of a back suspension bracket - removal and installation
15:11. Bars of a back suspension bracket - removal and
15:12. The stabilizer of a back suspension bracket - removal and installation
15:13. Steering - general information
15:14. A wheel - removal and installation
15:15. The lock of a steering column - removal and installation
15:16. A steering reducer - removal and installation
15:17. A steering reducer (the car without hydraulic booster) - dismantling
15:18. Steering
15:19. The pump hydraulic boosters - removal and installation
15:20. Removal of air from a wheel hydraulic actuator
15:21. Steering drafts - removal and installation
15:22. The angles of installation of forward wheels - general information
15:23. Wheels and tires - general information
16. Body and elements of finishing
17. System of electric equipment
 





15-8-verkhnijj-rychag-i-sharovaya-opora-snyatie-i-ustanovka.html

15.8. The top lever and a spherical support - removal and installation

1. You will lift a car front.
2. Remove a wheel.
3. Turn off the top nut of the shock-absorber and squeeze the shock-absorber.
4. Slightly raise a jack the lower lever.
5. Release a nut of the top hinge. Vypressuyte a stripper a support finger from an eye of a fist (photo). Turn off a nut.
6. Turn off bolts of fastening of an axis of the lever to a frame and remove the lever assembled with a support and adjusting washers. Pay attention to quantity and an order of an arrangement of adjusting washers (photo).
7. Turn off nuts and remove a support. The support non-demountable and in case of wear is replaced entirely.

7.5б Простейшее приспособление для выпрессовки опоры, изготовленное из болта, гайки и торцовой головки
7.5b the Elementary device for a support vypressovka manufactured of a bolt, a nut and a face head


7.5а Выпрессовка пальца верхней опоры с помощью приспособления
7.5a Vypressovka of a finger of the top support by means of adaptation



8. Replace the hardened or damaged plugs of the lever. For this purpose turn off nuts of an axis and a vypressuyta an axis from the lever (the press is required).
9. Before a press fitting of new plugs moisten them with soap solution. Plugs are pressed on a hydraulic press so that the fillet on the plug rested against reciprocal deepening in a lever sleeve.
10. Insert an axis and dress internal washers so that their rounded parties were turned inside.
11. Press external plugs.
12. Wrap axis nuts.
13. Install a support on the lever.
14. Install the lever, having tracked safety of adjusting washers. Tighten bolts with the set moment.

7.6 Болты крепления оси верхнего рычага подвески
7.6 Bolts of fastening of an axis of the top lever of a suspension bracket


7.15 Проверьте центровку рычага, измерив размеры А и В
7.15 Check centering of the lever, having measured the sizes A and B


8.8 Гайка оси нижнего рычага
8.8 Nut of an axis of the lower lever


9.3 Детали задней подвески 1.  Поперечная штанга 2. Продольная штанга 3. Верхняя штанга 4. Тяга стабилизатора 5. Стабилизатор 6. При заворачивании болтов и гаек правильно их сориентируйте. Болты и гайки должны соответствовать установленным изготовителем.
9.3 Details of a back suspension bracket 1. Cross bar 2. Longitudinal bar 3. Top bar 4. Draft of the stabilizer 5. Stabilizer 6. At a wraparound of bolts and nuts correctly orient them. Bolts and nuts have to correspond the established manufacturer.


15. Check the sizes A and B (photo). Compare them with specified in Specifications, if necessary adjust.
16. Other operations are carried out upside-down. Finally tighten bolts and nuts after lowering of the car on wheels. Check and adjust the angles of installation of wheels.


"previous page
15.7. Bars and extensions of a suspension bracket - removal and installation
following page"
15.9. The lower lever and a spherical support - removal and installation




9ac83ee2