Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
16.1. Specifications
16.2. Care of loops and locks
16.3. A windshield and motionless glasses of a body - replacement
16.4. Bumpers - removal and installation
16.5. A forward lattice - removal and installation
16.6. A forward apron - removal and installation
16.7. An air inlet lattice - removal and installation
16.8. A forward wing - removal and installation
16.9. Adjustment of a cowl
16:10. A cowl - removal and installation
16:11. Cowl locks - removal and installation.
16:12. A cowl lock drive cable - removal and installation
16:13. A back cover - removal and installation
16:14. The lock of a back cover and a cable of the drive - removal and installation
16:15. The internal panel of a door - removal and installation
16:16. Door glass and a window regulator - removal and installation
16:17. The door lock and handles - removal and installation
16:18. A door - removal and installation
16:19. A window leaf of side glass - removal and installation
16:20. Seats - removal and installation
16:21. Seat belts - general information
16:22. The central section - removal and installation
17. System of electric equipment
 





16-15-vnutrennyaya-panel-dveri-snyatie-i-ustanovka.html

16:15. The internal panel of a door - removal and installation

1. Lower glass.
2. Unscrew screws of fastening of an armrest to the panel.
3. Remove the window regulator handle for what the thin bent tool get a spring ring.
For this purpose wring out a decorative slip to get access to a shaft and a spring ring, hook a ring and displace towards the handle, and remove a ring. Remove the handle and a plastic washer.

14.5 Для снятия щитка рукоятки отверните один винт
14.5 For removal of a guard of the handle unscrew one screw


4. Remove the handle of the door lock.
5. Remove a decorative guard of the handle of a door (photo).
6. Hook the screw-driver and get panel latches from a framework of a door (photo). Begin to get latches from below and be displaced up, taking latches on a panel contour. Raise and remove the panel.
7. Before installation check a condition of all for. a lok be also convinced of correctness of orientation of the water filter.
8. Install the panel, being guided on it is inserted; to a koyatka of a window regulator.

14.6 Защелки крепления внутренней панели двери
14.6 Latches of fastening of the internal panel of a door


15.7 Детали двери и стеклоподъемника1. Регулировка двери2. Регулировка положения дверной петли3. Регулировка переднего желоба4. Регулировка механизма стеклоподъемника5. Регулировка положения стекла на стеклоподъемнике6. Регулировка фиксатора
15.7 Details of a door and window regulator
1. Adjustment of a door
2. Adjustment of provision of a door loop
3. Adjustment of a forward trench
4. Adjustment of the mechanism of a window regulator
5. Adjustment of situation flew down on a window regulator
6. Adjustment of a clamp



9. Insert latches to door framework openings (by hand or the plastic hammer).
10. Further installation is carried out upside-down. Fix the window regulator handle by a spring ring. For this purpose insert a spring ring into a groove on the handle so that the rupture of a ring was turned on 180 ° from the handle, expose the handle parallel to the handle on an opposite door and push a ring before click.


"previous page
16:14. The lock of a back cover and a cable of the drive - removal and installation
following page"
16:16. Door glass and a window regulator - removal and installation