Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
17.1. Specifications
17.2. General information
17.3. Search of malfunctions - the general of data
17.4. Safety locks - general information
17.5. Fusible crossing points - general information
17.6. The relay - general information
17.7. Switches - check
17.8. Indexes of turns and the alarm system - general information
17.9. Headlights - adjustment
17:10. Headlights - removal and installation
17:11. Lamps - replacement
17:12. A sound signal - check
17:13. A sound signal - removal and installation
17:14. Screenwash - the general of data
17:15. The glass cleaner electric motor - removal and installation
17:16. Windscreen washer - removal and installation
17:17. The block of switches on a steering column - removal and installation
17:18. The ignition switch - removal and installation
17:19. A guard of devices - removal and installation
17:20. The receiver - removal and installation
17:21. The lighter - removal and installation
17:22. The block of switches of lighting - removal and installation
17:23. The switch of the alarm system - removal and installation
17:24. The switch of a heater of back glass - removal and installation
17:25. A thermoelement of heating of back glass - removal and installation
17:26. Safety cushions - general information
17:27. Schemes assembly and electric basic
 






9ac83ee2

17-25-termoehlement-obogreva-zadnego-stekla-snyatie-i-ustanovka.html

17:25. A thermoelement of heating of back glass - removal and installation

1. The thermoelement consists of set horizontal a provolok, introduced in glass on formation stages.
2. Small damages a provolok can be eliminated independently, it is not required to remove glass.
3. To check work of a heater of back glass start the engine and include a heater.
4. Connect weighing one of wires of a control lamp, and other wire concern a heater wire.
5. Displace a wire along a wire from right to left, - lamp luminescence brightness at the same time has to increase. If brightness of a lamp is identical on both ends of a wire of a thermoelement, then it is necessary to check connection of a heater with weight. A wire it is necessary to check everything not less than two places.
6. Repair of a heater requires the special carrying-out paste with silver powder (is available on sale).
7. Switch off a heater and wait for cooling.
8. Slightly to a zapoliruyta the damaged site a soft steel sponge, wipe with alcohol.
9. Paste pieces of an adhesive tape on both sides of the damaged site so that the gap between pieces in accuracy coincided with the route of a wire on the damaged site.
10. Dip a poster feather into paste and draw a line on a gap between tape pieces so that the paste strip blocked the damaged site a little.
11. Carefully remove pieces of a tape and dry the put path an air soldering iron with a temperature of 250-350 °C within 1 - 2 min. from distance of 2-3 cm to glass.
12. If necessary restore color of the damaged site iodine tincture. It is possible to include the restored heater not less than in 24 hours.


"previous page
17:24. The switch of a heater of back glass - removal and installation
following page"
17:26. Safety cushions - general information