Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of the cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Lubricant of a running gear and steering
2.16. Check of a suspension bracket and steering
2.17. Check of the driveshaft
2.18. Check of the exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in the manual transmission
2.21. Check of level of oil in the transfer case
2.22. Check of level of oil and karteredifferentsiat (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ejector valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Replacement of oil in the transfer case
2.36. Replacement of oil in the manual transmission
2.37. Replacement of oil in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Replacement of lubricant in naves of forward wheels and check of bearings (only for rear wheel drive cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and the runner of a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





2-13-zamena-masla-i-maslyanogo-filtra.html

2.13. Replacement of oil and oil filter

1. Replacement of oil is the simplest operation which can be executed independently.
2. It is expedient to combine replacement of the filter with oil replacement.
3. Before works prepare all necessary tools and materials.
4. Install the car on a hole or a platform.
5. Wipe a drain stopper of the pallet.
6. Warm up the engine.
7. Oil changes on completely heated-up engine.
8. Substitute the pallet under a drain stopper and release a stopper.
9. Turn out a stopper, the last several turns rotate a stopper slowly (photo).
10. Merge oil in the substituted pallet.
11. After running off of oil wipe a stopper with pure rags (photo).
12. Wipe the pallet about a drain opening and wrap a stopper. Densely tighten a stopper with the set moment.
13. Rearrange the pallet under an oil filter.

13.9а Сливная пробка на двигателе V6
13:9á The Drain stopper on the V6 engine


13.9б Сливная пробка на 4-цилиндровом двигателе
13:9í The Drain stopper on the 4-cylinder engine


14. By means of a special key release an oil filter (photo)
13,14 (At the left) and 4-cylinder (on the right) to release an oil filter on the V6 engine
15. Turn out the filter hands.
16. Make sure that the type and the sizes of the new filter completely coincide with type and the sizes of fulfilled.
17. Wipe with pure rags the place of a prileganiye of the filter on the block of cylinders. Remove laying.
18. Slightly oil rubber laying of the new filter (photo) for the engine.
13:18 Before a wraparound of the filter oil laying of the filter fresh for the engine.
19. Wrap the filter and tighten the filter by hand.
20. Remove the tool and lower the car.
21. Fill in oil of the necessary brand through a stopper oil - a jellied mouth on a cover of a head of cylinders.
22. At first fill in about 0,8 l of oil then wait several minutes that all oil flew down in the pallet and the probe check oil level.
23. Continue to add oil in the small portions, before achievement of the mark "L". Start the engine that oil filled all lubricant channels.
24. Stop the engine and immediately check oil leaks, if necessary tighten a stopper or the filter.
25. Check level and if necessary add oil.
26. In we lie several trips after oil change especially you watch closely a leak and check oil level.

14.22 Порядок регулировки клапанов 1.  К передней части двигателя
14:22 Order of adjustment of valves 1. To a forward part of the engine


13.11 Металлические частицы, налипшие на магнитную пробку
13:11 The metal particles which stuck to a magnetic stopper



"previous page
2.12. Check and adjustment of a pedal of a brake
following page"
2.14. Check and adjustment of gaps of valves