Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of the cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Lubricant of a running gear and steering
2.16. Check of a suspension bracket and steering
2.17. Check of the driveshaft
2.18. Check of the exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in the manual transmission
2.21. Check of level of oil in the transfer case
2.22. Check of level of oil and karteredifferentsiat (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ejector valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Replacement of oil in the transfer case
2.36. Replacement of oil in the manual transmission
2.37. Replacement of oil in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Replacement of lubricant in naves of forward wheels and check of bearings (only for rear wheel drive cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and the runner of a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 

2-27-remni-privoda-proverka-regulirovka-i-zamena.html

2.27. Drive belts - check, adjustment and replacement

1. For the drive of units belts of wedge-shaped section are used.
2. The quantity of the belts established on the car depends on type of the engine and on a car complete set. The belt drive is provided for the generator, the pump of cooling liquid, the compressor of the conditioner and the power steering.

26.4 Насадок воздушного фильтра с термостатом
26.4 Nozzles of the air filter with the thermostat


26.5 Схема работы термостата 1. К датчику температуры воздуха 2. Вакуумный привод 3. Открыт 4. Закрыт 5. Холодный воздух 6. К карбюратору 7. Делительная заслонка 8. Горячий воздух от выпускного коллектора
26.5 Scheme of operation of the thermostat 1. To the sensor of air temperature 2. Vacuum drive 3. 4 is open. 5 are closed. Cold air 6. To the carburetor 7. Delitelny gate 8. Hot air from a final collector


3. The condition of belts is checked to the touch and survey (having lit belts with a small lamp). Check existence of peeling of the rubber pasted slip on both parties of a basis to basis anguish belts on end faces of a tape of a belt, hardening, damages of a surface of a belt (cracks, a separation and wear of paths, see a photo). Check also existence of wear and vitrification of material of a belt owing to which on a belt luster is observed. Overwind a belt and examine on both sides.
4. Check a belt tension. At distance between centers of pulleys from 170 to 280 mm the deflection of a belt has to be about 6 mm. If this distance from 300 to 400 mm, then a deflection there have to be about 13 mm (photo).
5. For adjustment of a tension special devices (photo) are provided.
6. For adjustment it is necessary to release bolts of fastening of the unit and to move the unit, having pulled a belt (or to rotate an adjusting bolt). Tighten boats of fastening and check a tension. If the tension is normal, then tighten bolts of fastening (photo). The tension of a gear belt is regulated by movement of a roller of a natyazhitel.

27.3 Некоторые характерные признаки износа ремня.1. Трещины2. Стеклование3. Попадание смазки4. Надрыв основы ремня
27.3 Some characteristic signs of wear of a belt.
1. Cracks
2. Vitrification
3. Lubricant hit
4. Belt basis anguish

7. It is recommended to change all belts at the same time.
"previous page
2.26. Check of the thermostat of the air filter		 following page"
2.28. Check of seat belts




9ac83ee2