Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of the cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Lubricant of a running gear and steering
2.16. Check of a suspension bracket and steering
2.17. Check of the driveshaft
2.18. Check of the exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in the manual transmission
2.21. Check of level of oil in the transfer case
2.22. Check of level of oil and karteredifferentsiat (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ejector valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Replacement of oil in the transfer case
2.36. Replacement of oil in the manual transmission
2.37. Replacement of oil in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Replacement of lubricant in naves of forward wheels and check of bearings (only for rear wheel drive cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and the runner of a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





2-45-proverka-i-ustanovka-momenta-zazhiganiya.html

2.45. Check and installation of the moment of ignition.

Attention!
On engines after 1990 the moment of ignition is regulated by automatically processor block.

45.4 Отметка на шкиве и шкала для установки зажигания на 4-цилиндровых двигателях
45.4 A mark in a pulley and a scale for installation of ignition on 4-cylinder engines


45.2 Отметка на шкиве и шкала для установки за жигания на 4-цилиндровых двигателях
45.2 A mark in a pulley and a scale for installation for zhiganiye on 4-cylinder engines


1. When checking an angle of installation of ignition be guided by data in the plate strengthened from the vnutry party of a cowl.
2. On 4-cylinder engines the moment of ignition is checked on combination of a mark in a pulley the crankshaft with division of the scale mounted over a pulley (photo) the Tag 0 there corresponds VMT.
3. Designate a mark in a pulley light paint
4. On the V6 engine the ignition moment the scale is checked on combination of the motionless index from division on the scale applied on a pulley of an uspokoitel (photo).
5. Check idling turns, if necessary adjust. Connect a stroboscope according to the instruction of the manufacturer.
6. Warm up the engine, stop and disconnect devices which are specified in the podkapotny plate for this engine
7. Attach a stroboscope according to the instruction from a gotovitel.
8. Start the engine, press 2-3 times the accelerator pedal and transfer to the idling mode.
9. Direct stroboscope light to a crankshaft pulley the Lit tag has to be opposite to the corresponding division of a scale.

45.11 Установка зажигания 1.  Увеличение угла опережения  2. Уменьшение угла
45.11 Installation of ignition 1. Increase in a corner of an advancing 2. Reduction of a corner


10. In need of adjustment release adjusting bolts of the distributor.
11. For installation of ignition turn the distributor case before combination of a tag with the necessary division of a scale (photo). Tighten bolts and again check installation of ignition.
12. Disconnect a stroboscope and check idling turns, if necessary adjust.
13. If at a trip ringing knocks at the movement of the car on rise are listened or at dispersals, then again attach a stroboscope and reduce an advancing corner on 1 - 2 °.

"previous page
2.44. A cover of the distributor and the runner of a rotor - check and replacement.
following page"
2.46. Oxygen sensor




9ac83ee2