Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





3-11-vypusknojj-kollektor-snyatie-i-ustanovka.html

3.11. A final collector - removal and installation

1. Disconnect air ejection tubes, remove the case of valves (if it is provided).
2. Disconnect the channel connecting a collector and the air filter.
3. Remove a thermal guard.
4. Disconnect a tube of recirculation (photo).
5. Lift a forward part of the car and establish on supports.
6. Disconnect a forward exhaust pipe.
7. Disconnect wires from candles from a final collector.
8. Turn off bolts and nuts of a collector.

11.4 Трубки эжекции воздуха (слева) и рециркуляции (справа) на выпускном коллекторе двигателя   Z24i
11.4 Air ejection tubes (at the left) and recirculation (on the right) on a final collector  of the Z24i engine


12.13а Последовательность ослабления болтов головки цилиндров на двигателях Z24
12.13a the Sequence of weakening of bolts of a head of cylinders on Z24 engines


12.13б Последовательность ослабления болтов головки цилиндров на двигателях К24
12.13b the Sequence of weakening of bolts of a head of cylinders on K24 engines


13.2 Головка цилиндров двигателя К241  Валики коромысел и коромысла клапанов2. Головка цилиндров3. Прокладка4. Болт5. Распредвал6. Седло7. Направляющая втулка8. Опорная шайба9. Маслосъемный колпачок10. Сухари11. Тарелка12. Впускной
13.2 Head of cylinders of the K24 engine
1 Rollers of yokes and yoke of valves
2. Head of cylinders
3. Laying
4. Bolt
5. Cam-shaft
6. Saddle
7. The directing plug
8. Basic washer
9. Oil scraper cap
10. Crackers
11. Plate
12. Inlet


9. Disconnect a collector.
10. Clear a collector of the consolidation remains.
11. Establish new laying on a head of cylinders. Tighten by hand bolts and nuts.
12. In 3-4 receptions tighten bolts and nuts with the set moment. Tighten from the center to the periphery in a cross order.
13. Other operations are carried out upside-down.
20. Warm up, the engine and be convinced of tightness of connections of a collector.

"previous page
3.10. The soaking-up collector - removal and installation
following page"
3.12. A head of cylinders - removal




9ac83ee2