Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

3-14-maslyanyjj-nasos-snyatie-i-ustanovka.html

3.14. The oil pump - removal and installation

1. Install the piston 1 - го the cylinder in compression step VMT.
2. Uncover the distributor of ignition and obo4 mean position of the runner concerning the distributor case.
3. Lift a forward part of the car and establish on supports.
4. Remove engine mudguards.
5. Merge oil from the engine.
6. On cars with a formula 4x4 establish a support under a forward reducer.
7. Turn off bolts and remove the pump assembled with shaft.
8. The order of dismantling of the pump is described in below.
9. Make sure that the piston of the 1st cylinder is in compression step VMT.
10. Fill the pump with oil, combine a tag to a pile) the pump with a lubricant opening under the leading gear wheel (photo).
11. Establish laying and the pump.
12. Tighten bolts and check orientation of a shaft coca. If necessary repeat operation устаноааЩ
13. Fill in oil. Check installation of ignition

14.10 При установке насоса метка на валу  должна  быть напротив смазочного отверстия насоса
14:10 At installation of the pump the tag on a shaft has to be opposite to a lubricant opening of the pump


15.1 Детали масляного насоса1, Вал2,4- Прокладка3. Корпус5.  Шестерни (ведущая и ведомая)6. Крышка7. Заглушка8. Шайба9. Пружина10. Клапан11. Редукционный клапан
15.1 Details of the oil pump
1, Shaft
2,4-Laying
3. Case
5. The gear wheels (conducting and conducted)
6. Cover
7. Cap
8. Washer
9. Spring
10. Valve
11. Reducing valve


"previous page
3.13. A head of cylinders - installation
following page"
3.15. The oil pump - check