Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





3-17-perednijj-salnik-kolenvala-zamena.html

3.17. A forward epiploon of the crankshaft - replacement

17. A forward epiploon of the crankshaft - replacement
1. Remove a pulley.
2. Carefully get an epiploon, having hooked it the screw-driver or other tool (photo).
3. Clear an opening under an epiploon and slightly oil an external surface of a new epiploon for the engine. Carefully press a new epiploon into place by means of a mandrel with a diameter a little smaller what diameter of an epiploon (photo). After installation be convinced that the provision of a spring of an epiploon is not violated.
4. Establish a pulley.
5. Establish other details. Start the engine and be convinced of lack of a leak.

17.2 Передний сальник коленвала
17.2 Forward epiploon of the crankshaft


17.3 Запрессовка сальника
17.3 Epiploon press fitting


18.14а При снятии крышки не повредите переднюю часть прокладки головки цилиндров
18.14a At removal of a cover do not damage a forward part of laying of a head of cylinders


18.14б Передняя крышка двигателя К241.  Коленвал2. Звездочка коленвала3. Маслоотражатель4. Шкив5. Сальник6. Крышка7. Башмак натяжителя и успокоитель цепи8. Натяжитель9. Звездочка10. Цепь
18.14b Forward cover of the K24 engine
1. Crankshaft
2. Crankshaft asterisk
3. Maslootrazhatel
4. Pulley
5. Epiploon
6. Cover
7. Boot of a natyazhitel and uspokoitel of a chain
8. Natyazhitel
9. Asterisk
10. Chain



"previous page
3.16. A crankshaft pulley - removal and installation
following page"
3.18. A forward cover - removal and installation




9ac83ee2