Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





3-20-maslyanyjj-poddon-snyatie-i-ustanovka.html

3.20. The oil pallet - removal and installation

1. Merge oil.
2. Lift a forward part of the car and establish on supports.
3. Remove engine mudguards.
4. On cars with a formula 4x9 remove a stretcher.
5. On cars with a formula 4x4 remove a forward reducer, you will hang out the engine, having weakened support. Record support wooden whetstones.
6. Turn off bolts and remove the oil pallet. At removal do not damage the demountable planes of the block of cylinders and the pallet.

19.14в На двигателе К24 звено с серебристой окраской должно быть совмещено с меткой на звездочке распредвала
19.14v On the K24 engine the link with silvery coloring has to be combined with a tag on a cam-shaft asterisk


19.15а Отведите в сторону успокоитель.
19.15a Take aside an uspokoitel.


19.15б Зазор между корпусом натяжителя и башмаком после сборки должен отсутствовать1. Натяжитель2. После сборки
19.15b the Gap between the case of a natyazhitel and a boot after assembly has to be absent
1. Natyazhitel
2. After assembly


21.2 Снятие маховика
21.2 Removal of a flywheel


7. Carefully clear the demountable planes of the block of cylinders and the pallet of the consolidation remains. Wash out the condensed planes solvent of varnishes or acetone. Be convinced of purity of carving openings in the block of cylinders.
8. Check existence on the demountable plane of the pallet of deformations, especially about openings under bolts. If necessary align the demountable plane the hammer, having laid on a wooden board.
9. Apply on the pallet plane RTV sealant with a thin layer and lay laying.
10. Install the pallet and evenly in a cross order tighten bolts with set, the moment. In 30 min. (after a sealant skhvatyvaniye) fill in oil, start the engine and be convinced of lack of leaks.

"previous page
3.19. A chain and asterisks - removal and installation
following page"
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation




9ac83ee2