Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





3-3-poryadok-ustanovki-porshnya-1-go-cilindra-v-vmt-takta-szhatiya.html

3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.

1. On a pulley of the crankshaft the mark for exposure of the piston 1 - го the cylinder is provided in compression step VMT.
2. Installation of the piston (or pistons) in VMT of a step of compression is an integral part of many procedures.
3. Transfer the check point lever to neutral situation. Disconnect a high-voltage wire of the coil of ignition from the central conclusion of a cover of the distributor and connect to weight on the block of cylinders.

3.5б Шкала на шкиве (двигатель К24) 1. Метка красного цвета 2. Шкала для установки зажигания
3.5b the Scale on a pulley (K24 engine) 1. Tag of red color 2. A scale for installation of ignition


4. Uncover the distributor and find on a cover the provision of a high-voltage wire of a candle 1 - го the cylinder. If this conclusion is not numbered, then determine it by a wire from a spark plug.
5. Turn the crankshaft a key or a starter so that the mark in a pulley was combined with a tag About on a scale. The normal direction of rotation of the engine - clockwise (photo).
5. If the runner indicates the tag put on the distributor case, then the piston 1 - го the cylinder is in compression step VMT. Otherwise tighten the crankshaft on one whole revolution clockwise (360 °) and install the piston of the 1st cylinder in compression step VMT.
6. Now it is possible to expose in VMT of a step of compression and other pistons, turning the crankshaft on 180 ° and observing an operating procedure of cylinders.

"previous page
3.2. Types of the repair work performed without dismantle of the engine from the car
following page"
3.4. A cover of a head of cylinders - removal and installation