Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

3-6-valik-s-koromyslami-razborka-i-sborka.html

3.6. The roller with yokes - dismantling and assembly

1. Remove all bolts except for two bolts on both ends.
2. Holding the roller, carefully get 2 extreme bolts, allowing to be straightened springs.
3. Remove yokes and designate so that at assembly to establish on former places.
4. Replace rollers if on them there are wear signs.

6.5а Ориентация валиков коромысел при сборке (двигатель Z24)1.Пазы2. Кернения3. Валик выпускных клапанов4. Валик впускных клапанов5. К передней части двигателя
6.5a Orientation of rollers of yokes at assembly (Z24 engine)
1. Grooves
2. Kerneniya
3. Roller of final valves
4. Roller of inlet valves
5. To a forward part of the engine


6.5б Установочные метки на кронштейнах валиков и на головке цилиндров 1.  К передней части двигателя 2. Метки на кронштейнах 3. Метки на головке цилиндров
6.5b Adjusting tags on arms of rollers and on a head of cylinders 1. To a forward part of the engine 2. Tags on arms 3. Tags on a head of cylinders


6.5в Ориентация скоб при сборке валиков с коромыслами (двигатель K24J 1,2. Вырез 3. Со стороны впускных клапанов 4. Со стороны выпускных клапанов
6.5v Orientation of brackets at assembly of rollers with yokes (the K24J 1,2 engine. Cut 3. From inlet valves 4. From final valves





7.6 Отворачивание болта звездочки распредвала
7.6 Otvorachivaniye of a cam-shaft asterisk bolt


7.8 Фиксация цепи клином
7.8 Fixing of a chain wedge


7.12 Перед установкой смажьте шейки распредвала
7.12 Before installation grease cam-shaft necks


5. Install the roller in a forward arm, combine openings and insert bolts. On the roller of inlet valves grooves are provided. At assembly install rollers so that kerneniye at their end faces were turned up. Establish arms being guided on tags (photo).
6. Dress yokes, squeeze a spring and establish back arms, insert bolts. Install rollers and a cover upside-down.

"previous page
3.5. The roller with yokes - removal and installation
following page"
3.7. A cam-shaft - removal and installation