Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
3.1. General information
3.2. Types of the repair work performed without dismantle of the engine from the car
3.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
3.4. A cover of a head of cylinders - removal and installation
3.5. The roller with yokes - removal and installation
3.6. The roller with yokes - dismantling and assembly
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and yokes - check
3.9. Springs of valves and oil scraper caps - replacement
3.10. The soaking-up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A crankshaft pulley - removal and installation
3.17. A forward epiploon of the crankshaft - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a drive plate of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





3-chetyrekhcilindrovyv-dvigateli.html

3. Четырехцилиндровыв engines




Specifications (all sizes in mm)
Numbering of cylinders
1-2-3-4
Operating procedure
1-3-4-2
Working volume of engines:
The Z24J type (after 1987)
2389 cm3
The KA24E type (after 1990)
2389 cm3
Gaps in valves See Gl.1

Z24i if K24 engines (in brackets different data of day of the engine are specified: K24, other data are identical)
Raspredvap

Diameter of basic necks 32,935 - 32,955

Axial side play
0,2
Sizes of cams
38,477-38,527 (44,839-45,0291
Extreme wear
0,25
Beating in the center of an average basic neck
0,2
Diameter of support
33,000-33,025
Gap in basic necks of a cam-shaft
0,045-0,090
Oil pump
Gap in gearing of gear wheels:
Standard
0,12
Limit
0,20
Gap between the conducted gear wheel and a pump housing
Standard
0,15-0,21
Limit
0,50
Face gap 0,06
Deformation of the plane of a pump housing
no more than 0,03

The inhaling moments (in N. of m).
Cam-shaft asterisk bolt
110-130
Bolts of a natyazhitel and uspokoitel of a chain
6-9(7-11)
Bolt of a pulley of a kolenvap
110-130
Bolts of a head of the block of cylinders:
1st stage of an inhaling
27
2nd stage
70
3rd stage
Completely
to weaken bolts
4th stage
27
5th stage
65-75
Bodta of a final collector
15-18
Bolts of fastening of a flywheel (drive plate of the hydrotransformer)
115-125(85-96)
Bolts of fastening of a cover of a head of cylinders
1-3(3,6-7,2)
Bolts of a forward cover (only for Z24i)
M6 bolts
4-8
M8 bolts
8,5-14
Bolts and nuts of the soaking-up collector
15-18
Bolts and nuts of the oil pallet
4-6
Bolts of the oil pump
10-14
Bolts of rollers of yokes
14-22 (32,4-36)

Порядок соединения свеч с распределителем на двигателе Z24i
Order of connection of candles with the distributor on the Z24i engine


Расположение цилиндров и направление вращения распределителя
Arrangement of cylinders and direction of rotation of the distributor


3.5а Отметка на шкиве деление О на шкале для установки поршня в ВМТ.
3.5a the Mark in a pulley division About on a scale for installation of the piston in VMT.


"previous page
2.46. Oxygen sensor
following page"
3.1. General information




9ac83ee2