Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work performed without dismantle of the engine from the car
4.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. The soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the valvate mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a drive plate of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





4-13-golovki-cilindrov-snyatie-i-ustanovka.html

4.13. Heads of cylinders - removal and installation

1. Execute a decompression of fuel system, disconnect the battery from weight and a speyta liquid.

12.4 Метки й и L на звездочках распре два лов )
12.4 Tags й and L on asterisks conflicts two fishing)


12.5б Запрессовка сальника (используется такое же   приспособление, что и для сальника коленвала)
12:5í An epiploon Press fitting (the same  adaptation, as for a crankshaft epiploon is used)


13.3 Болты крепления задней крышки зубчатого ремня
13.3 Bolts of fastening of a back cover of a gear belt


2. You will take off a gear belt, the case of the gate, a vsasye the howling collector, asterisks of cam-shafts.
3. You will turn off bolts and remove a back cover of a belt (photo).
13.7а Порядок отпускания болтов головки цилиндров1. К передней части
13:7á Order of an otpuskaniye of bolts of a head of cylinders
1. To a forward part


13.8 Болт  в  нижней части головки цилиндров
13.8 A bolt in the lower part of a head of cylinders


13.14а Ориентация шайб головки цилиндров1. В  сторону головки
13.14a Orientation of washers of a head of cylinders
1. Towards a head


Removal of the left head
4. Remove the compressor and take aside, without disconnecting the highway.
5. Remove the distributor, the generator, an arm of the generator and a final collector.
6. Remove details of the valvate mechanism.
7. Evenly and gradually turn off bolts of a head of cylinders and you store them in an initial order (photo).
8. Turn off a small bolt in the lower part of a head (photo) and carefully remove a head.
Right head
9. Remove the pump of the hydraulic booster and take aside.

13.7б Один из способов хранения болтов на выкройке прокладки головки цилиндров (можно снять с новой прокладки). Обозначьте переднюю часть, а также правую и левую стороны головки цилиндров
13:7í One of ways of storage of bolts on a pattern of laying of a head of cylinders (it is possible to remove from new laying). Designate a forward part, and also the right and left parties of a head of cylinders


13.13 Сориентируйте прокладку по штифтам на блоке цилиндров
13:13 Orient laying on pins on the block of cylinders


13.14б Порядок затягивания болтав головки. Болты 4,5,12 и 13 длиннее остальных1. Правая головка2. Левая головка
13.14b Order of tightening of bolts of a head. Bolts 4,5,12 and 13 are longer than the others
1. Right head                      
2. Left head


14.3 Болты торцовой крышки.
14.3 Bolts of a face cover.


14.4б ... отверните центральный болт
14:4í... turn off the central bolt


10. Remove a final collector, details of the valvate mechanism and turn off bolts of a head of cylinders (see above).
11. Turn off a small bolt in the lower part of a head and carefully remove a head of cylinders
Installation
12. Carefully clear the demountable planes of the block and a head, polish small roughnesses, banish and clear all carving openings.
13. Lay new laying (photo) on the block.
14. Wrap by hand bolts of a head of cylinders on former places. A flat part of washers of bolts has to be turned towards a head of cylinders (photo).
15. Tighten bolts in 5 stages with the set moment in the specified sequence (photo).
16. Other operations are carried out upside-down. Replace oil and the filter.

"previous page
4.12. A cam-shaft epiploon - replacement
following page"
4.14. A cam-shaft - removal and installation