Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work performed without dismantle of the engine from the car
4.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. The soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the valvate mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a drive plate of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





4-16-maslyanyjj-poddon-snyatie-i-ustanovka.html

4.16. The oil pallet - removal and installation

1. Disconnect the battery from weight.

15.86 Измерение диаметра отверстия в коромысле.
15.86 Measurement of diameter of an opening in a yoke.


15.6б ... и отверстия под толкатель в корпусе I
15:6í... and openings under a pusher in the case I


15.8а Диаметр валика измеряется в месте расположения коромысла
15:8á Diameter of the roller is measured in the location of a yoke


2. Lift a forward part of the car and establish on supports.
3. Remove a guard of a case and merge oil.
4. Remove a starter.
5. Remove brackets of fastening of a bell-shaped case to the engine.
6. Remove the pendular lever.
7. On cars 4x2 remove stability stabilizer arms.
8. On cars 4x2 remove a stretcher.
9. On cars 4x4 remove an arm передня a reducer.

16.17а Нанесите герметик в места прилегания держателя заднего сальника и масляного насоса
16.17a Apply sealant to places of a prileganiye of the holder of a back epiploon and the oil pump  


16.17б Места нанесения герметика на прокладку поддона1. Прокладка
16.17b Places of putting sealant on laying of the pallet
1. Laying


17.3а Болты масляного насоса
17:3á Bolts of the oil pump


10. Remove transmission support.
11. Disconnect exhaust pipes from collectors.
12. You will hang out the power unit on a waist or establish under it a jack.
13. Turn off bolts of fastening of support of the engine to a frame.
14. Raise the engine a little, being careful.
15. Turn off bolts and remove the pallet.
16. Carefully clear the demountable planes of the block of cylinders and the pallet of the consolidation remains. Banish and clear carving openings in the block of cylinders.
17. Apply sealant (photo) on the demountable planes.
18. Install laying on the pallet, install the pallet and evenly in a cross order tighten bolts with the set moment (photo).

"previous page
4.15. Details of the valvate mechanism - check
following page"
4.17. The oil pump - removal, check and installation