Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work performed without dismantle of the engine from the car
4.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. The soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the valvate mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a drive plate of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





4-17-maslyanyjj-nasos-snyatie-proverka-i-ustanovka.html

4.17. The oil pump - removal, check and installation

Removal
1. Take off a gear belt, a pulley and the pallet.
2. Turn off bolts and remove an oil receiver.
3. Turn off bolts of the oil pump and remove the pump, having displaced blows through a wooden pig (photo).
4. Clear the pump.
Check
5. Uncover and wash out all details in solvent. Turn off a cap and get the reducing valve (photo).

16.18 Порядок затягивания болтов поддона1.  К передней части двигателя
16:18 Order of tightening of bolts of the pallet
1. To a forward part of the engine


17.3б Снятие масляного насоса
17:3í Removal of the oil pump


17.5 Детали масляного насоса1. Внутренняя шестерня2. Наружная шестерня
17.5 Details of the oil pump
1. Internal gear wheel
2. External gear wheel


6. Check gaps of the pump (photo). If one of gaps differs from norm, then replace couple of gear wheels or the pump.
7. Fill a cavity of a naos with technical vaseline and collect the pump.
Installation
8. Grease with sealant the demountable plane of the pump.
9. Establish all details upside-down, having replaced all laying and a sealant (photo).

17.6а Проверка зазора между наружной шестерней и корпусом насоса (А), между внутренней шестерней и серповидной вставкой (В) и между наружной шестерней и серповидной вставкой (С)
17:6á Check of a gap between an external gear wheel and a pump housing (A), between an internal gear wheel and a crescent insert (V) and between an external gear wheel and a crescent insert (C)


17.6б Проверка торцового зазора
17:6í Check of a face gap


17.9 Замена уплотнительного кольца маслоприемника
17.9 Replacement of a sealing ring of an oil receiver



"previous page
4.16. The oil pallet - removal and installation
following page"
4.18. A back epiploon - replacement




9ac83ee2