Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work performed without dismantle of the engine from the car
4.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. The soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the valvate mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a drive plate of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





4-4-kryshki-golovok-cilindrov-snyatoe-i-ustanovka.html

4.4. Covers of heads of cylinders – removed and installation

1. Execute a decompression of fuel system.

3.4а Отметка О на шкиве и указатель
3.4a Mark O in a pulley and index


3.4б Когда деление О на шкиве совпадет с указателем...1.  Шкала установки зажигания
3.4b When division About on a pulley will coincide with the index...
1. Scale of installation of ignition


3.5 ...а бегунок указывает на нанесенную метку, то поршень 1-го цилиндра находится в ВМТ такта сжатия 1. Бегунок
3.5... and the runner indicates the put tag, the piston of the 1st cylinder is in VMT of a step of compression 1. Runner


2. Disconnect the battery from weight.
Right cover
3. Disconnect a hose of ventilyation of a case (photo)
4. Designate and disconnect from wire candles, take them aside.
5. Disconnect hoses and wires from a cover.
6. Unscrew screws of a cover and remove washers.
4.3 Шланги и провода, которые надо отсоединить, чтобы снять правую крышку головки цилиндров
4.3 Hoses and wires which should be disconnected to remove the right cover of a head of cylinders


4.8 Шланга и провода, которые надо отсоединить, чтобы  снять  левую крышку головки цилиндров
4.8 A hose and a wire which should be disconnected to remove the left cover of a head of cylinders


5.3 Уложите болты валиков в кассу в порядке им установки
5.3 Lay bolts of rollers in cash desk as it should be to them installations


7. Uncover, having carefully opened consolidation.
Left cover
8. Disconnect a hose of a sapun (Photo) from a cover.
9. Designate and disconnect from wire candles.
10. Get from wire arms.
11. Unscrew 9 screws and uncover.
Installation
12. Clear a cover of the consolidation remains, apply sealant in a cover flute and lay laying. After a skhvatyvaniye of sealant establish a cover and wrap screws.
13. Evenly tighten screws in 3-4 receptions.
14. Other procedures are performed upside-down.
15. Warm up the engine and be convinced of lack of a leak

"previous page
4.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
following page"
4.5. The roller with yokes - removal and installation