Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
5.1. General information
5.2. Check of a compression in engine cylinders
5.3. Dismantle of the power unit - a security measure
5.4. The engine - removal and installation
5.5. Capital repairs of the engine - general information
5.6. Restoration of the engine - an alternative
5.7. Capital repairs of the engine - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. Head of the block of cylinders cleanings and check of a state
5.10. A head of cylinders - assembly
5.11. Conrod and piston group dismantle
5.12. The crankshaft - dismantle
5.13. The block of cylinders - cleaning
5.14. The block of cylinders - check of a state
5.15. Rods and pistons - check of a state
5.16. The crankshaft - check of a state
5.17. Radical and conrod bearings - check and selection
5.18. Capital repairs of the engine - an assembly order
5.19. Piston rings - installation
5.20. The crankshaft - installation and check of gaps of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of gaps in conrod bearings
5.23. Launch of the engine after repair and a running in
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





5-10-golovka-cilindrov-sborka.html

5.10. A head of cylinders - assembly

1. Be convinced of purity of a head of cylinders.
2. Establish basic washers of springs.
3. Napressuyte on the new oil scraper caps directing plugs by means of a mandrel or adaptation (photo). Rotation of caps at a napressovka is not allowed
4. Oil a valve core for the engine and install the first valve. Install a plate and crackers and check spring height in working order (i.e. distance between a basic washer and the lower surface of a plate in position of the closed valve, a photo). If necessary adjust height installation of additional basic washers.

10.3 Напрессовка колпачков с помощью приспособления
10.3 Napressovka of caps by means of adaptation


10.4 Проверка высоты пружины в рабочем состоянии
10.4 Check of height of a spring in working order


5. Remove a plate and crackers and establish both springs by a dense navivka (photo) down.
6. Squeeze springs and establish crackers. If necessary grease crackers with jellied lubricant temporarily to fix on a core of the valve (photo).
7. Similarly install other valves. Again check height of springs (photo) and adjust basic washers. Installation of excess basic washers is not allowed if the initial height of a spring in working order meets standard.

10.5  Ориентация пружин клапанов при сборке
10.5 Orientation of springs of valves at assembly


10.6 Смажьте сухари для закрепления на стержне клапана
10.6 Grease crackers for fixing on a valve core


10.7  Повторная проверка высоты пружин
10.7 Repeated check of height of springs


11.1 Удаление буртика в  цилиндре с помощью ра звертки
11.1 Removal of a fillet in the cylinder with the help ра zvertka    


11.3  Маркировка шатуна с указанием номера цилиндра
11.3 Marking of a rod with the indication of number of the cylinder


8. Establish a cam-shaft, rollers with yokes and pushers (on V6 engines).
9. On 4 - cylinder engines adjust gaps in valves, having established gaps for the cold engine.

"previous page
5.9. Head of the block of cylinders cleanings and check of a state
following page"
5.11. Conrod and piston group dismantle