Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
5.1. General information
5.2. Check of a compression in engine cylinders
5.3. Dismantle of the power unit - a security measure
5.4. The engine - removal and installation
5.5. Capital repairs of the engine - general information
5.6. Restoration of the engine - an alternative
5.7. Capital repairs of the engine - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. Head of the block of cylinders cleanings and check of a state
5.10. A head of cylinders - assembly
5.11. Conrod and piston group dismantle
5.12. The crankshaft - dismantle
5.13. The block of cylinders - cleaning
5.14. The block of cylinders - check of a state
5.15. Rods and pistons - check of a state
5.16. The crankshaft - check of a state
5.17. Radical and conrod bearings - check and selection
5.18. Capital repairs of the engine - an assembly order
5.19. Piston rings - installation
5.20. The crankshaft - installation and check of gaps of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of gaps in conrod bearings
5.23. Launch of the engine after repair and a running in
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

5-11-shatunno-porshnevaya-gruppa-demontazh.html

5.11. Conrod and piston group dismantle

Attention!
Before removal of pistons and rods remove a head of cylinders, the oil pallet and the oil pump.

1. Remove a fillet in the top part of the cylinder (photo).
2. Turn the engine and check an axial side play of rods (photo), inserting probes between the crankshaft and a rod. The axial side play will be equal to the total thickness of probes at which the side play disappears. If the axial side play of a rod exceeds standard value, then the rod should be replaced. If new rods are established (or the crankshaft), then the axial side play can be less norm (in this case it is necessary to proshlifovat rods, if necessary consult in a workshop of car service). Repeat the procedure for other rods.

11.2  Поверка  осевого люфта шатуна
11.2 Checking of an axial side play of a rod


11.4а Оденьте на болты отрезки шлангов..
11:4á Dress pieces of hoses on bolts.


3. In the absence of tags on rods and covers of rods to a nakernita on  them number of the corresponding cylinder (photo).
4. Weaken an inhaling of nuts of covers, turning off them on 1/2 turns at one time until nuts do not begin to turn away by hand. Uncover a rod of the first cylinder together with an insert, do not take an insert from a cover. Push out the piston with a rod and an insert through the top part of the cylinder, previously having dressed pieces of hoses (photo) on bolts.
5. Repeat the procedure for all other cylinders.
6. Collect rods with covers, tighten nuts of covers by hand.

"previous page
5.10. A head of cylinders - assembly
following page"
5.12. The crankshaft - dismantle