Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
5.1. General information
5.2. Check of a compression in engine cylinders
5.3. Dismantle of the power unit - a security measure
5.4. The engine - removal and installation
5.5. Capital repairs of the engine - general information
5.6. Restoration of the engine - an alternative
5.7. Capital repairs of the engine - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. Head of the block of cylinders cleanings and check of a state
5.10. A head of cylinders - assembly
5.11. Conrod and piston group dismantle
5.12. The crankshaft - dismantle
5.13. The block of cylinders - cleaning
5.14. The block of cylinders - check of a state
5.15. Rods and pistons - check of a state
5.16. The crankshaft - check of a state
5.17. Radical and conrod bearings - check and selection
5.18. Capital repairs of the engine - an assembly order
5.19. Piston rings - installation
5.20. The crankshaft - installation and check of gaps of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of gaps in conrod bearings
5.23. Launch of the engine after repair and a running in
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

5-13-blok-cilindrov-ochistka.html

5.13. The block of cylinders - cleaning

Attention!
If caps of channels of the cooling system fail to the canal of the block of cylinders, then it is impossible to take them, as a rule.

1. Drill in caps of an opening and pull out, having wrapped bolts or self-tapping screws, or get a stripper with the bent pads.
2. Carefully clear the block of the remains of consolidation (photo).
3. Uncover radical bearings and get bearings from the block of cylinders and covers. Designate all details that not to mix them.
4. Clean all channels a vapor jet and compressed air (it is recommended to carry out in car service), wash out the block outside detergent. Banish all carving openings, clean and blow compressed air (photo). Dry the block and oil the processed surfaces veretenny.

12.3  Снятие крышек на 4 -цилиндровых двигателях
12.3 Removal of covers on 4 - cylinder engines


13.4 Прогонка резьбового отверстия
13.4 Pro-race of a carving opening


5. Establish covers of radical bearings, tighten bolts by hand.
13.6 Запрессовка заглушки
13.6 Cap press fitting


14.2а Измерьте диаметр цилиндра под буртикам (А), в центре (В) и в нижней части (С)
14:2á Measure diameter of the cylinder under fillets (A), in the center (V) and in the lower part (C)


14.2в Измерение диаметра цилиндра
14:2ó Measurement of diameter of the cylinder


14.3а Щетка для хоннингования цилиндров
14:3á The Brush for a honningovaniye of cylinders


14.2б Телескопический нутромер для измерения внутреннего диаметра
14:2í The Telescopic nutromer for measurement of internal diameter


6. Press new caps without distortions, previously having greased them with RTV sealant (photo).

"previous page
5.12. The crankshaft - dismantle
following page"
5.14. The block of cylinders - check of a state