Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
5.1. General information
5.2. Check of a compression in engine cylinders
5.3. Dismantle of the power unit - a security measure
5.4. The engine - removal and installation
5.5. Capital repairs of the engine - general information
5.6. Restoration of the engine - an alternative
5.7. Capital repairs of the engine - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. Head of the block of cylinders cleanings and check of a state
5.10. A head of cylinders - assembly
5.11. Conrod and piston group dismantle
5.12. The crankshaft - dismantle
5.13. The block of cylinders - cleaning
5.14. The block of cylinders - check of a state
5.15. Rods and pistons - check of a state
5.16. The crankshaft - check of a state
5.17. Radical and conrod bearings - check and selection
5.18. Capital repairs of the engine - an assembly order
5.19. Piston rings - installation
5.20. The crankshaft - installation and check of gaps of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of gaps in conrod bearings
5.23. Launch of the engine after repair and a running in
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2 юридическая помощь королев
установка музыки
термопринтер чеков
На http://yukka-dveri.su межкомнатные двери недорого с установкой под ключ.

5-16-kolenval-proverka-sostoyaniya.html

5.16. The crankshaft - check of a state

1. Wash out a bent shaft solvent and dry, clean oil channels, necks and remove agnails (photo).
2. Check a condition of necks of a shaft. Measure diameter of necks in several places and define conicity and ovality (photo). Check a beating of the crankshaft having established in prisms.
3. In the presence of damages on shaft necks and also if ovality, conicity and wear of necks exceed the set limits, the shaft should be pereshlifovat and replaced radical and conrod bearings repair.
4. If on necks under epiploons the deep flute of development from a working edge of an epiploon was formed, there are scratches or other damages, then the crankshaft is recommended to be replaced.

16.1  Удалите  заусенцы с края  смазочного отверстия
16.1 Remove agnails from edge of a lubricant opening


15.8 Измерение зазора между канавкой и новым кольцом
15.8 Measurement of a gap between a flute and a new ring


15.9 Измерение диаметра поршня. Диаметр измеряется перпендикулярно оси пальца 1.20,3  мм
15.9 Measurement of diameter of the piston. Diameter is measured perpendicular to an axis of a finger of 1.20,3 mm


16.2 измерение диаметра шеек коленвала
16.2 measurement of diameter of necks of the crankshaft


17.4а Места нанесения номеров размерных групп коренных подшипников на 4-цилиндровых двигателях1.  К передней части двигателя2. Группа В3. Размерная группа коренных шеек
17:4á Places of drawing numbers of dimensional groups of radical bearings on 4-cylinder engines
1. To a forward part of the engine
2. Group B
3. Dimensional group of radical necks



"previous page
5.15. Rods and pistons - check of a state
following page"
5.17. Radical and conrod bearings - check and selection