Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
6.1. The cooling system - general information
6.2. Antifreeze - general information
6.3. The thermostat - removal and
6.4. A radiator - removal and installation
6.5. The fan and the coupling - removal and installation
6.6. A tank - removal and
6.7. The pump of cooling liquid - check
6.8. The pump of cooling liquid - removal and installation
6.9. The liquid temperature sensor - check and replacement
6.10. System of heating - general information
6.11. The fan - removal and installation
6.12. A heater radiator - removal and installation
6.13. Air conditioning system - general information
6.14. Air conditioning system - service
6.15. The proofreader of idling - adjustment
6.16. A moisture separator - removal and installation
6.17. The compressor - removal and installation
6.18. The condenser - removal and installation
6.19. The control panel of a heater and the conditioner - removal, installation and adjustment
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





6-12-radiator-otopitelya-snyatie-i-ustanovka.html

6.12. A heater radiator - removal and installation

1. Merge cooling liquid.
2. On cars with the conditioner disconnect shlz-ng on a partition of a motor compartment (photo)
3. On cars without conditioner remove a casing of a radiator (photo) and disconnect hoses on a partition of a motor compartment.
4. Remove the central section (if it is provided).
5. Disconnect a cable of the delitelny gate from a fan casing.
6. On cars with the conditioner remove the fan, turn off nuts and bolts of the block of cooling.
7. Unscrew screws and having raised, remove a heater.
8. Remove the control panel (see below).
9. If necessary sort a heater for what disconnect drafts of the lever of mixing and delitelny gates, remove latches and disunite both half of a casing (photo). At installation adjust drafts (see below).

11.3б Вентилятор установлен справа под перчаточным ящиком1.Разъем2. Болт3. Шланг
11:3í The Fan is installed under a glove box on the right
1. Socket
2. Bolt
3. Hose


12.2 Шланги отопителя
12.2 Heater hoses


12.3 Детали отопителя и кондиционера1,2,13. Размораживающее сопло3. Кожух4. Воздухозаборник5,8. Воздуховод6. Сопла для обогрева салона7.  Нижний  воздуховод кондиционера8.Отопитепь10,12. Кронштейн11 .  Кондиционер
12.3 Details of a heater and conditioner
1,2,13. The defreezing nozzle
3. Casing
4. Air inlet
5,8. Air duct
6. Nozzles for heating of salon
7. Lower air duct of the conditioner
8. Отопитепь 
10,12. Arm
11. Conditioner


12.9 Радиатор отопителя и кожух1.  Смесительная заслонка2. Дренажный кран3. Делительная заслонка4. Заслонка вентиляционного сопла5. Радиатор
12.9 Radiator of a heater and casing
1. Mixing gate 
2. Drainage crane
3. Delitelny gate
4. Gate of a ventilating nozzle
5. Radiator



"previous page
6.11. The fan - removal and installation
following page"
6.13. Air conditioning system - general information




9ac83ee2