Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
6.1. The cooling system - general information
6.2. Antifreeze - general information
6.3. The thermostat - removal and
6.4. A radiator - removal and installation
6.5. The fan and the coupling - removal and installation
6.6. A tank - removal and
6.7. The pump of cooling liquid - check
6.8. The pump of cooling liquid - removal and installation
6.9. The liquid temperature sensor - check and replacement
6.10. System of heating - general information
6.11. The fan - removal and installation
6.12. A heater radiator - removal and installation
6.13. Air conditioning system - general information
6.14. Air conditioning system - service
6.15. The proofreader of idling - adjustment
6.16. A moisture separator - removal and installation
6.17. The compressor - removal and installation
6.18. The condenser - removal and installation
6.19. The control panel of a heater and the conditioner - removal, installation and adjustment
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





6-17-kompressor-snyatie-i-ustanovka.html

6.17. The compressor - removal and installation

1. Transfer rychazhka of management to the provision of the maximum cooling, open windows and sustain the compressor included for 10 min. idling.

15.5 Регулировочный винт корректора холостого хода на инжекторном двигателе1.Винт2. Электромагнитный клапан корректора
15.5 The adjusting screw of the proofreader of idling on the injector engine
1. Screw
2. Electromagnetic valve of the proofreader


16.3 Влагоотделитель кондиционера1. Трубка от конденсатора2. Выпускная трубка3. Датчик давления4. Болт хомута
16.3 Conditioner moisture separator
1. A tube from the condenser
2. Final tube
3. Pressure sensor
4. Collar bolt


2. Disconnect the battery from weight and remove the ignition distributor.
3. Turn off a bolt of a natyazhitel of a belt on a compressor pulley, turn an adjusting bolt and take off a belt (photo).
4. Disconnect from the compressor of a tube of the highway (photo).
5. Disconnect all wires from the compressor. -
6. Turn off bolts and remove the compressor from an arm (photo).
7. Get the compressor from a compartment.

Attention!
In order to avoid breakage working position of the compressor should not be broken for the period of more than 10 min. If the normal provision nevertheless was violated, then install the compressor into position and turn a shaft on several turns.

8. Installation is carried out upside-down. At accession of tubes replace sealing rings. Fill the conditioner in car service.

17.3 Болт натяжитапя на шкиве компрессора (А) и регулировочный болт (В) на двигателе V6
17.3 A bolt натяжитапя on a pulley of the compressor (A) and an adjusting bolt (V) on the V6 engine


17.6 Компрессор и кронштейн
17.6 Compressor and arm



"previous page
6.16. A moisture separator - removal and installation
following page"
6.18. The condenser - removal and installation