Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
6.1. The cooling system - general information
6.2. Antifreeze - general information
6.3. The thermostat - removal and
6.4. A radiator - removal and installation
6.5. The fan and the coupling - removal and installation
6.6. A tank - removal and
6.7. The pump of cooling liquid - check
6.8. The pump of cooling liquid - removal and installation
6.9. The liquid temperature sensor - check and replacement
6.10. System of heating - general information
6.11. The fan - removal and installation
6.12. A heater radiator - removal and installation
6.13. Air conditioning system - general information
6.14. Air conditioning system - service
6.15. The proofreader of idling - adjustment
6.16. A moisture separator - removal and installation
6.17. The compressor - removal and installation
6.18. The condenser - removal and installation
6.19. The control panel of a heater and the conditioner - removal, installation and adjustment
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





6-19-panel-upravleniya-otopitelem-i-kondicionerom-snyatie-ustanovka-i-regulirovka.html

6.19. The control panel of a heater and the conditioner - removal, installation and adjustment

1. Disconnect the battery from weight. Remove a tray for trifles (if it is provided).
2. Disconnect from the fan and from a heater cables. The lever of a temperature regulator is recommended to be transferred to situation Cold.
3. Remove from rychazhok of the handle (photo) and remove the control panel.
4. Unscrew screws (photo), get the panel and disconnect sockets.
5. If necessary remove and check the fan switch (Hl. 12). The switch is disconnected from the panel.

17.4 Магистрали отсоединяются от компрессора после отворачивания этих болтов
17.4 Highways are disconnected from the compressor after an otvorachivaniye of these bolts


19.3 Для снятия рукояток подайте их прямо на себя.
19.3 For removal of handles give them directly on yourself.


19.3 Снимите с рычажков рукоятки и снимите панель управления.
19.3 Remove from rychazhok of the handle and remove the control panel.


19.4 Отвернете винты, достаньте панель и отсоедините разъемы.
19.4 You will unscrew screws, get the panel and disconnect sockets.


6. Installation is carried out upside-down. Adjust drafts of control of gates.
Adjustment
7. For adjustment of drafts of the delitelny gate and the gate of the defreezing nozzle at first disconnect a cable of side draft and adjust draft of the delitelny gate. Attach a cable and adjust.
8. For adjustment of draft of control of the gate of a ventilating air duct displace side draft in the direction of an arrow (photo). Holding the top and lower levers in the lower situation, attach in the order of draft 1 and 2 to the corresponding levers.
9. For adjustment of draft of control of the gate of the defreezing nozzle displace side draft in the direction of an arrow (photo). Having given the lever of the gate of the defreezing nozzle in the direction of an arrow, attach a rod to side draft.
10. For adjustment of a cable of management of airinflow give a cover of a cable and side draft in the direction of an arrow. Record a cover a collar in this situation.
11. For adjustment of draft of the crane of a heater disconnect a cable of a temperature regulator from the lever of the mixing gate and adjust draft. Attach a cable and adjust. Give the lever of the mixing gate in the direction of an arrow (photo). Translate draft of the crane of a heater in the direction of an arrow that between draft and the lever there were about 2 mm and attach thirst for the gate lever.

19.10 Регулировка троса управления воздухопритоком1. Боковая тяга2. Подать в этом направлении3. Хомут4. Крайнее положение
19:10 Adjustment of a cable of management of airinflow
1. Side draft
2. To give in this direction
3. Collar
4. Extreme situation


19.8 Регулировка тяги управления заслонкой вентиляционного воздуховода1.  Рычаг заслонки верхний2. Рычаг заслонки нижний3. Подать в этом направлении4. Боковая тяга5. Заслонки 1 и 2
19.8 Adjustment of draft of control of the gate of a ventilating air duct
1. Gate lever top
2. Gate lever lower
3. To give in this direction
4. Side draft
5. Gates 1 and 2


19.9 Регулировка тяги управления заслонкой размораживающего сопла1. Рычаг заслонки2. Боковая тяга3. Подать в этом направлении4. Шток
19.9 Adjustment of draft of control of the gate of the defreezing nozzle
1. Gate lever
2. Side draft
3. To give in this direction
4. Rod


19.11 Регулировка тяги крана отопителя1. Подать2. Потянуть3. Рычаг тяги управления краном4. Тяга5. Рычаг смесительной заслонки
19:11 Adjustment of draft of the crane of a heater
1. Tax
2. To pull
3. Lever of draft of control of the crane
4. Draft
5. Lever of the mixing gate


19.12 Регулировка троса терморегулятора1. Смесительная заслонка2. Подать3. Положение максимального охлаждения
19:12 Adjustment of a cable of a temperature regulator
1. Mixing gate
2. Tax
3. Provision of the maximum cooling


12. For adjustment of a cable of a temperature regulator displace a rychazhok (photo) to the left, give a cover of a cable and the lever of the gate in the direction of an arrow and record a cover a collar.

19.13 Регулировка троса заслонки воздухозаборника1. Рычаг заслонки воздухозаборника2. Хомут3. Подать в этом направлении4. Положение рычажка управления
19:13 Adjustment of a cable of the gate of an air inlet
1. Air inlet gate lever
2. Collar
3. To give in this direction
4. Situation rychazhka of management


13. For adjustment of a cable of the gate of an air inlet displace a rychazhok to the full to the left (photo), give a cover of a cable and the lever of the gate in the direction of an arrow and record a cover a collar.

"previous page
6.18. The condenser - removal and installation
following page"
7. Fuel and exhaust systems