Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
7.1. Fuel system - general information
7.2. The fuel filter - replacement
7.3. Idling turns - check and adjustment
7.4. The fuel highway - repair
7.5. A cable of the drive of a butterfly valve - removal and installation
7.6. A pedal - removal and installation
7.7. The fuel pump - check
7.8. The fuel pump - removal and installation
7.9. System of electronic injection of fuel - general information
7.10. Units of control and measuring system with the processor ECCS block - general information
7.11. Decompression of fuel system
7.12. The case of a butterfly valve (for systems with preliminary injection of TBI of systems) removal and installation
7.13. Nozzle replacement
7.14. System of injection of fuel – adjustment System of preliminary injection (TBI)
7.15. Fuel system cleaning
7.16. Tank removal and installation
7.17. Fuel level sensor removal and installation
7.18. Tank washing
7.19. Exhaust system general information
7.20. Forward exhaust pipe removal and installation
7.21. Catalytic neytralizatorsnyaty and installation
7.22. Muffler removal and installation
7.23. Average pipe removal and installation
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

7-5-tros-privoda-drosselnojj-zaslonki-snyatie-i-ustanovka.html

7.5. A cable of the drive of a butterfly valve - removal and installation

1. Remove the air filter.
2. Disconnect a cable from the case of the gate (photo).

4.1 Топливная магистраль двигателей с впрыском топлива1. Трубка подачи топлива2. Обратный бензопровод3. Трубка отбора паров бензина4. Контрольный клапан5. Датчик уровня топлива6. Насос7. Прокладка8. Бак9. Щиток бака (на полноприводных а/
4.1 The fuel highway of engines with fuel injection
1. Fuel supply tube
2. Return fuel pipe
3. Tube of selection of vapors of gasoline
4. Control valve
5. Fuel level sensor
6. Pump
7. Laying
8. Tank
9. A tank guard (on all-wheel drive and /


3. Give on yourself a cuff and get a cable from a cut in an arm (photo).
4. Turn off bolts of the directing tube and extend a cable through a partition (photo).
5. Installation is carried out upside-down. Grease a cuff with jellied lubricant. Check work of a cable, having pressed a pedal, - the gate has to open completely. Adjust a cable rotating a cable cover nut. On cars with automatic transmission when pressing a pedal the rod of the switch of a low gear (switch kick-down-) has to be involved completely.

5.2а Чтобы отсоединить трос заслонки или круиз-контроля отверните гайки и достаньте оболочку троса. Затем стяните муфты на петлях тросов и достаньте тросы.
5.2a to disconnect a cable of the gate or a cruise control turn off nuts and get a cable cover. Then pull together couplings on loops of cables and get cables.


5.2б Педаль и привод дроссельной заслонки1.  Рычаг заслонки2. Трубка3. Нейлоновая манжета4. Контргайка5. Кронштейн и пружина6. Педаль7. Рычаг8. Трос9. Хомут
5.2b Pedal and drive of a butterfly valve
1. Gate lever
2. Tube
3. Nylon cuff
4. Lock-nut
5. Arm and spring
6. Pedal
7. Lever
8. Cable
9. Collar


5.3 Отсоединение троса от педали
5.3 A cable detachment from a pedal


6. On cars about a cruise - control (the automatic regulator of speed) at first adjust a cable of a butterfly valve, then - a regulator cable.

"previous page
7.4. The fuel highway - repair
following page"
7.6. A pedal - removal and installation