Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
7.1. Fuel system - general information
7.2. The fuel filter - replacement
7.3. Idling turns - check and adjustment
7.4. The fuel highway - repair
7.5. A cable of the drive of a butterfly valve - removal and installation
7.6. A pedal - removal and installation
7.7. The fuel pump - check
7.8. The fuel pump - removal and installation
7.9. System of electronic injection of fuel - general information
7.10. Units of control and measuring system with the processor ECCS block - general information
7.11. Decompression of fuel system
7.12. The case of a butterfly valve (for systems with preliminary injection of TBI of systems) removal and installation
7.13. Nozzle replacement
7.14. System of injection of fuel – adjustment System of preliminary injection (TBI)
7.15. Fuel system cleaning
7.16. Tank removal and installation
7.17. Fuel level sensor removal and installation
7.18. Tank washing
7.19. Exhaust system general information
7.20. Forward exhaust pipe removal and installation
7.21. Catalytic neytralizatorsnyaty and installation
7.22. Muffler removal and installation
7.23. Average pipe removal and installation
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

7-9-sistema-ehlektronnogo-vpryska-topliva-obshhie-svedeniya.html

7.9. System of electronic injection of fuel - general information

Cars are equipped with system or preliminary preparation of mix (TBI system) or direct injection of fuel in cylinders (MPF system). Systems of injection of both types are run by the processor ECCS block and work together with many units of system of decrease in toxicity of exhaust gases. Such system is known as system of electronic injection (EFI) and consists of 3 subsystems - control and measuring, dispensing of fuel and injection of air. The amount of injectable fuel is defined by duration of an open condition of a nozzle which is automatically regulated by the ECCS block on the basis of the data which are read out from various sensors.

7.4а Установка манометра дл
7.4a Installation of the manometer


7.4, Схема включения контрольного манометра на двигателе К241. Регулятор давления2. Манометр3. Топливный фильтр4. Бак5. Насос6. Форсунка
7.4, the Scheme of turning on of the control manometer on the K24 engine
1. Pressure regulator
2. Manometer
3. Fuel filter
4. Tank
5. Pump
6. Nozzle


7.4в Установка манометра для проверки насоса на двигателях V6 с прямым впрыском топлив. Манометр присоединяется между фильтром и магистралью со стороны двигателя.
7.4v Installation of the manometer for check of the pump on V6 engines with direct injection of fuels. The manometer joins between the filter and the highway from the engine.



9.1а Агрегаты системы прямого впрыска двигателя К241. Датчик выхлопных газов 2. Катушка  зажигания с силовым транзистором 3. Электромагнитный клапан 4. Распределитель зажигания 5. Датчик вращения коленвала 6. Расположение измерителя скорости потока 7.
9.1a Units of system of direct injection of the K24 engine
1. Sensor of exhaust gases 2. The ignition coil with the power transistor 3. Electromagnetic valve 4. Distributor of ignition 5. Sensor of rotation of the crankshaft 6. Arrangement of the measuring instrument of speed of a stream 7. 


1. Датчик температуры выхлопных газов (только для штата Калифорния) 2. Регулятор потока воздуха 3. Пневмоклапан рециркуляции 4. Бачок с поглотителем 5. Датчик скорости потока 6. Электромагнитный клапан рециркуляции 7. Датчик поворота дроссельной заслонки
1. The sensor of temperature of exhaust gases (only for the State of California) 2. Air 3 stream regulator. Pneumatic valve of recirculation 4. A tank with an absorber 5. Sensor of speed of a stream 6. Electromagnetic valve of recirculation 7. Sensor of turn of a butterfly valve


9.1б Агрегаты системы прямого впрыска двигателя V6
9.1b Units of system of direct injection of the V6 engine


Necessary precautionary measures
а). It is forbidden to switch-off the battery on the working engine.
б). Before depressurization of system execute a decompression.
в). Before removal of any unit of system disconnect the battery from weight and turn the ignition key in situation Off.
г). Conducting plaits" systems have to lie not less than in 10 mm from other plaits (including an antenna cable),
д). Check reliability of all connections as in bad contacts there will be a sparking from breakdown in candles and the ignition block will fail.
е). Before launch of the engine it is forbidden to press a pedal of a butterfly valve.
ж). Keep in mind that several relays operate operation of the fuel pump. After an engine stop the pump is switched-off under the influence of signals of pressure drop and tension on the generator.

"previous page
7.8. The fuel pump - removal and installation
following page"
7.10. Units of control and measuring system with the processor ECCS block - general information