Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
7.1. Fuel system - general information
7.2. The fuel filter - replacement
7.3. Idling turns - check and adjustment
7.4. The fuel highway - repair
7.5. A cable of the drive of a butterfly valve - removal and installation
7.6. A pedal - removal and installation
7.7. The fuel pump - check
7.8. The fuel pump - removal and installation
7.9. System of electronic injection of fuel - general information
7.10. Units of control and measuring system with the processor ECCS block - general information
7.11. Decompression of fuel system
7.12. The case of a butterfly valve (for systems with preliminary injection of TBI of systems) removal and installation
7.13. Nozzle replacement
7.14. System of injection of fuel – adjustment System of preliminary injection (TBI)
7.15. Fuel system cleaning
7.16. Tank removal and installation
7.17. Fuel level sensor removal and installation
7.18. Tank washing
7.19. Exhaust system general information
7.20. Forward exhaust pipe removal and installation
7.21. Catalytic neytralizatorsnyaty and installation
7.22. Muffler removal and installation
7.23. Average pipe removal and installation
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 





7-toplivnaya-i-vykhlopnaya-sistemy.html

7. Fuel and exhaust systems




Specifications of engines with injections of fuel (K24 and U6), the sizes and gaps are given in mm
Check and adjustment of turns of idling
For engines with preliminary injection (preparation of gas mixture)
G gap (between the roller of draft and a cam, see the text)
0,5-3,0
Installation of a gap of G at adjustment
0,8-2,0
Installation of a gap for engines with direct injection of fuel (K24)
From the manual transmission
2,3
With automatic transmission
2,1
Adjusting data of the automatic proofreader of idling
Idling turns (at the switched-off conditioner)
Cars from the manual transmission
4-cylinder engine
900+50 rpm
V6
800+50 rpm
Cars with automatic transmission
4-cylinder engine
650+50 rpm
V6
700±50 rpm
Idling turns at the switched-on conditioner (transmission in situation N)
900+50 rpm
Turns at which the rod of the pneumoshock-absorber adjoins to the lever of a butterfly valve
4-tsilindroy engine
1600±50 rpm
V6
1300±50 rpm
Fuel pump
Fuel pressure (in kgf/cm2)
For engines with preliminary preparation of gas mixture
2,3
For engines with direct injection of fuel
V6 engine
With additional depression
2,1
Without depression
2,7
K24 engine
With additional depression
2,05
Without depression
2,7

The inhaling moments (in N. of m)
Nuts of the case of a butterfly valve
Till 1992.
11-15,5
C1993 of.
1st stage of an inhaling
8-10
2nd stage
16-20
Bolts of the electromagnetic valve of a cut-off of fuel
23
Drain stopper of the fuel tank
48
Bolts of a back arm of the fuel tank
45
Bolts of fastening of the fuel tank
Till 1990.
8,5
Since 1991.
24-32
Bolts of fastening of catalytic converter

Till 1990.
33
Since 1991 for the Pathfinder car V6 engine
38-50
Bolts of fastening of a forward exhaust pipe to final a stake - to the lecturer
To.1990 g.
20
Since 1991 for the Pathfinder car V6 engine
36-42

"previous page
6.19. The control panel of a heater and the conditioner - removal, installation and adjustment
following page"
7.1. Fuel system - general information




9ac83ee2