Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
8.1. Specifications
8.2. System of ignition general information
8.3. System of ignition check
8.4. Distributor removal
8.5. Distributor installation
8.6. Sensor of rotation of the crankshaft check
8.7. Ignition coil removal and installation
8.8. System of launch of the engine general information
8.9. System of launch of the engine check
8.10. Starter removal and installation
8.11. Traction relay removal and installation
8.12. Starter replacement of brushes
8.13. System of a charge general information
8.14. Generator leaving and precautionary measures
8.15. System of a charge check
8.16. Generator removal and installation
8.17. Regulator of tension and brush replacement
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment
 






9ac83ee2

8-12-starter-zamena-shhetok.html

8.12. Starter replacement of brushes

Starter without reducer
1. Remove a starter and the traction relay.
2. Remove a back sealant (photo).

11.2б Детали стартера (без редуктора) заднеприводных автомобилей с 4цилиндровым двигателем 1. Тяговое реле 2. Якорь 3. Уплотнитель 4. Стопорная шайба 5. Упорная шайба 6. Задняя крышка 7. Задняя втулка 8.  Щеткодержатель 9. Щетка () 10. Щетка (+) 11. Ярмо
11:2í Starter Details (without reducer) rear wheel drive cars with 4 cylinder engine 1. Traction relay 2. Anchor 3. Sealant 4. Lock washer 5. Persistent washer 6. Back cover 7. Back plug 8. Brush holder 9. Brush () 10. Brush (+) 11. Yoke


11.2в Детали стартера (без редуктора) полноприводных автомобилей с 4цилиндровым двигателем 1.  Регулировочные прокладки (толщина 0,5 или 0,8 мм) 2. Тяговое реле 3. Задняя крышка 4. Ярмо 5. Обмотка возбуждения 6. Щетка (+) 7. Якорь 8. Щеткодержатель 9. Рыч
11:2ó Starter Details (without reducer) all-wheel drive cars with 4 cylinder engine 1. Adjusting laying (thickness of 0,5 or 0,8 mm) 2. Traction relay 3. Back cover 4. Yoke 5. Winding of excitement 6. Brush (+) 7. Anchor 8. Brush holder 9. Рыч


11.6 Щеткодержатель стартере
11.6 Brush holder starter


11.12 Отведите пружины и достаньте щетки 1. Щеткодержатель 2. Крючок 3. Щетка
11:12 Take away springs and get brushes 1. Brush holder 2. Hook 3. Brush


11.9а  Детали стартера (с редуктором) автомобилей с 4цилиндровым двигателем 1. Тяговое реле 2. Регулировочная прокладка (уплотнитель) 3. Пружина 4. Рычаг 5. Передняя крышка 6. Корпус редуктора 7. Прокладка 8. Ведущая шестерня  9,18. Кольцо 10. Якорь 11. О
11:9á Starter Details (with a reducer) cars with 4 cylinder engine 1. Traction relay 2. Adjusting laying (sealant) 3. Spring 4. Lever 5. Forward cover 6. Case of a reducer 7. Laying 8. Leading gear wheel 9,18. Ring 10. Anchor 11. About


11.9б Детали стартера (с редукторам) автомобилей с двигателем V6 1. Тяговое реле 2.Орбитальная шестерня 3. Задняя крышка 4. Уплотнитель 5. Болт 6. Якорь 7. Ярмо 8. Перегородка 9. Шайбы 10. Щеткодержатель 11. Планетарные шестерни 12. Ведущая шестерня 13. Ш
11:9í Starter Details (with reducers) cars with the V6 1 engine. Traction relay 2. Orbital gear wheel 3. Back cover 4. Sealant 5. Bolt 6. Anchor 7. Yoke 8. Partition 9. Washers 10. Brush holder 11. Planetary gear wheels 12. Leading gear wheel 13. Ш


14.4 Фиксация щеток отрезком проволоки
14.4 Fixing of brushes wire piece


3. Get a lock ring and a persistent washer.
4. On a back cover unscrew two screws of the brush holder.
5. Turn out coupling bolts and remove a back cover.
6. Get the brush holder (photo), take away springs and get brushes. If height of brushes is less than 12 mm, then unsolder them and solder new.
7. Collect a starter upside-down.
Starter with a reducer
8. Remove a starter and the traction relay.
9. Turn out coupling bolts (photo).
10. Remove a back cover, without having damaged a ring.
11. Separate from a cover a yoke assembled with an anchor and the brush holder.
12. Take away springs and get brushes from the brush holder (photo), unsolder and solder new (if height of brushes less norm).
13. Collect a starter upside-down.

"previous page
8.11. Traction relay removal and installation
following page"
8.13. System of a charge general information