Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
2.1. Introduction
2.2. Maintenance terms
2.3. An order of performance of adjustments - general comments
2.4. Check of level of liquids
2.5. Check of level of liquid in automatic transmission
2.6. Check of level of liquid of the power steering
2.7. Check of tires (through each 400 kilometers or weekly)
2.8. Care of the battery
2.9. Care of the cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and oil filter
2.14. Check and adjustment of gaps of valves
2.15. Lubricant of a running gear and steering
2.16. Check of a suspension bracket and steering
2.17. Check of the driveshaft
2.18. Check of the exhaust system
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in the manual transmission
2.21. Check of level of oil in the transfer case
2.22. Check of level of oil and karteredifferentsiat (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and filter of ventilation of a case
2.30. Replacement of the fuel filter
2.31. Replacement of the filter of the ejector valve of system of a dookisleniye exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case of a butterfly valve
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Replacement of oil in the transfer case
2.36. Replacement of oil in the manual transmission
2.37. Replacement of oil in a reducer back (or forward) the bridge
2.38. Replacement of transmission liquid! in automatic transmission
2.39. Replacement of lubricant in naves of forward wheels and check of bearings (only for rear wheel drive cars)
2.40. Replacement of cooling liquid
2.41. Check and replacement of a zolotnik of ventilation of a case
2.42. Replacement of spark plugs
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and the runner of a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. Oxygen sensor
3. engines
4. VS engines
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment



2.4. Check of level of liquids

1. Before check install the car on the flat horizontal platform.
Oil in the engine
2. Level of oil is checked by the probe (photo).
3. Level of oil is checked before driving on the car, or about 15 minutes later after an engine stop.
4.4     1.  2.  3.  4.   V65.  4-
4.4g Arrangement of marks in the oil probe
1. Normal level
2. Type A
3. Type B
4. On V6 engines
5. On 4-cylinder engines

4.4  4-   8
4.4b On 4-cylinder engines with 8 candles the probe is located in the left back part of the engine

4.4   V6
4.4v On V6 engines the probe is located in a back part of the engine near the amplifier of brakes

4. Get the control probe from a tube and wipe it pure rags or a tissue. Insert the pure probe against the stop into a branch pipe and again get. Level has to be between marks L (at least) and N (at most).
5. Support oil level only between the specified marks.
6. Add oil through a mouth on a cover of a head of cylinders (photo).
4.6     V6
4.6 The mouth stopper on the V6 engine is on the right cover of a head of cylinders

4.8 Broad tank of the cooling system

7. Attentively check a condition of oil on the probe. Emulsion pollution can be caused by cracks in the block or in a head of cylinders, and also laying destruction therefore it is necessary to check a condition of the engine.
Cooling liquid
8. All cars considered in this manual have the cooling system of elevated pressure with return of liquid to a broad tank (photo).
9. On the cold engine level has to be between marks of "MIN' and "MOVE" on a broad tank On the heated-up engine level can be near the mark "MAH". If it is necessary to restore level, then wait for cooling of the engine, uncover a broad tank and add liquid of necessary structure antifreeze/water (50/50 are recommended).
10. After a trip check level again.
4.14 Tank

11. Need of a frequent dolivaniye indicates violation of tightness of system. Check existence on a radiator, hoses and demountable connections of traces of dribbles in the form of spots, or uvlazhneniye. If strong indications of a leak are not revealed, it is recommended to check a radiator stopper, and tightness of all system by a pressure testing method (giving of pressure) for car repair shops.
12. To turn off a stopper of a mouth of a radiator only on the cooled-down engine.
13. At detection of traces of pollution wash out system and replace liquid.
Liquid in a washer reservoir.
14. The tank of windscreen washer is in a motor compartment from the driver (photo).
15. In a temperate climate in a tank of windscreen washer clear water approximately on 2/3 tanks is filled in. In a frigid climate liquid of special structure is filled in.
16. To prevent fogging in cold weather, before inclusion of a smyvatel warm up glass from defreezing heater nozzle.
Check of level of electrolyte
17. New cars are completed with batteries with the transparent case in which the level of electrolyte is visible through the case (photo). If necessary add the distilled water.
Restoration of level of liquid in a hydraulic actuator of brakes and couplings
18. The main cylinder of brakes and its tank are mounted on the vacuum amplifier in a motor compartment. The main cylinder of coupling is mounted on a partition of a motor compartment.
19. Level of liquid has to be between the marks min and max in tanks (photo).
20. In a tank of brakes add only liquid of the recommended brand, mixing of liquids of various brands is not allowed.

Brake fluid makes harmful effects on eyes and destroys a paint and varnish covering therefore filling in liquid be careful. Brake fluid absorbs moisture from air therefore it is forbidden to fill in liquid which was a long time in an open container in brakes. Excess of moisture leads to dangerous loss of efficiency of braking.

21. At detection of pollution liquid should be merged and replaced.
22. After restoration of level densely wrap a tank stopper.

4.17 ,
4.17 Marks between which there has to be electrolyte level

4.19a liquid Level has to be in a tank of brakes about the top tag

23. During normal work of system liquid level gradually goes down in process of wear of brake slips. If frequent addition of brake fluid is required, then in a hydraulic actuator of system there is a leak which should be eliminated immediately.
24. If level liquid in tanks is lower than norm, then it is necessary to remove air from a hydraulic actuator.

"previous page
2.3. An order of performance of adjustments - general comments
following page"
2.5. Check of level of liquid in automatic transmission