Nissan Terrano 2 from 1985 to 1999
1. Maintenance instruction and to maintenance
2. Maintenance of the car
3. Четырехцилиндровыв engines
4. VS engines
4.1. General information
4.2. Types of the repair work performed without dismantle of the engine from the car
4.3. Order of installation of the piston of the 1st cylinder in compression step VMT.
4.4. Covers of heads of cylinders – removed and installation
4.5. The roller with yokes - removal and installation
4.6. Hydropushers - removal and installation
4.7. The soaking-up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - an uspokoitel - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon of the crankshaft - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details of the valvate mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a drive plate of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Cooling systems, heating, ventilation and conditioning
7. Fuel and exhaust systems
8. System of electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. Mechanical transmission
11. Automatic transmissions
12. Coupling driveshaft and back bridge
13. A running gear of cars with a wheel formula 4x4
14. Brake system
15. Suspension brackets and steering
16. Body and elements of finishing
17. System of electric equipment



4.7. The soaking-up collector - removal and installation

1. Depressurize fuel system and disconnect the battery from weight.
2. Merge liquid.
3. Remove the air filter, the case of a butterfly valve, disconnect wires from candles and uncover the distributor.
4. Disconnect the recirculation valve.
5. Take off a belt of the conditioner and an arm of a roller of a natyazhitel of this belt (photo).

7.5 Болты крепления ролика натяжителя ремня кондиционера
7.5 Bolts of fastening of a roller of a natyazhitel of a belt of the conditioner

7.9 Порядок отпускания болтов всасывающего коллектора
7.9 An order of an otpuskaniye of bolts of the soaking-up collector

6. Disconnect from the thermostat a hose perepuskny a hose and the top hose of a radiator.
7. Designate from a collector and disconnect vacuum hoses, wires and cables.
8. Disconnect a heater hose in a back part of a collector.
9. Evenly turn off bolts and nuts in the specified sequence and carefully remove the soaking-up collector.
10. Clear a collector, banish all carvings.
11. Establish new laying on the collector (having recorded according to the instruction attached to this detail).
12. Without violating the provision of laying, establish a collector and wrap bolts and nuts. Evenly tighten bolts and nuts with the set moment, in the specified sequence (photo).
13. Other operations are carried out in the return sweat a row.

8.4 Детали правого выпускного коллектора1. Прокладка2,3. Тепловые щитки4. Коллектор
8.4 Details of the right final collector
1. Laying
2,3. Thermal guards
4. Collector

7.12 Порядок затягивания болтов всасывающего коллектора
7.12 An order of tightening of bolts of the soaking-up collector

"previous page
4.6. Hydropushers - removal and installation
following page"
4.8. A final collector - removal and installation